![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
| The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History | |
WD hand cultch removal |
Post Reply
|
| Author | |
19F150
Bronze Level
Joined: 13 Oct 2025 Location: eastern ia Points: 25 |
Post Options
Thanks(0)
Quote Reply
Topic: WD hand cultch removalPosted: 06 Jun 2026 at 4:00pm |
|
How do you remove hand cultch assembly?
|
|
![]() |
|
| Sponsored Links | |
![]() |
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009 Points: 23548 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jun 2026 at 6:18pm |
|
Battery box has to be removed and then the tractor split apart about 8 inches right there. Hand clutch comes up and out the hole directly underneath the battery box.
|
|
![]() |
|
Gary
Orange Level Access
Joined: 13 Sep 2009 Location: Peterborough,On Points: 5913 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jun 2026 at 6:23pm |
|
Page 34 in Part 1 of the Allis WD Service Manual gives a good explanation. G |
|
![]() |
|
19F150
Bronze Level
Joined: 13 Oct 2025 Location: eastern ia Points: 25 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jun 2026 at 9:52pm |
|
how do you get the handclutch housing apart from the transmison
|
|
![]() |
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009 Points: 23548 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jun 2026 at 10:03pm |
|
Remove three 1/2" bolts on each side of the torque housing probably covered in dirt/grease. Remove two side frames bolts at the rear of each side frame. Brake pedal rods and springs disconnect. Steering wheel post disconnect from the transmission shift cover. PTO push/pull lever remove. Traction Booster signal linkage remove. Hand clutch clevis pin remove. That's about it I think. Roll the rear end away from the front. Use jacking under the PTO box. Use long redi-bolt thru the side frames ears to keep things under control. Why are you removing the hand clutch ??
|
|
![]() |
|
19F150
Bronze Level
Joined: 13 Oct 2025 Location: eastern ia Points: 25 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Jun 2026 at 10:25pm |
|
have all bolts removed and toque tube still won't come off from transmission
|
|
![]() |
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009 Points: 23548 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Jun 2026 at 10:50pm |
|
Have you got the PTO shaft removed from the tractor ??
|
|
![]() |
|
19F150
Bronze Level
Joined: 13 Oct 2025 Location: eastern ia Points: 25 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 Jun 2026 at 7:16am |
|
PTO shaft is off. torque moved about 1/4 inch is all
|
|
![]() |
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009 Points: 23548 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 Jun 2026 at 7:20am |
|
Hand clutch released?? or still locked in ? The bottle jack under the PTO box might have to be raised or lowered just a tick. You might be on a bind.
Edited by DrAllis - 08 Jun 2026 at 7:22am |
|
![]() |
|
HudCo
Orange Level
Joined: 29 Jan 2013 Location: Plymouth Utah Points: 4236 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 Jun 2026 at 8:44am |
|
is nt their a bolt inside the trans
|
|
![]() |
|
LaJaMe
Bronze Level
Joined: 14 Sep 2014 Location: wisconsin Points: 173 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 Jun 2026 at 9:38pm |
|
As Dr Allis Says, Neewd to support the middle of the tractor.
|
|
![]() |
|
Post Reply
|
|
|
Tweet
|
| Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |