This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


8000 Issues (Dr Allis)
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Unit3 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 17 Oct 2009
Location: NC Iowa
Points: 5598 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Unit3 Quote  Post ReplyReply Direct Link To This Post Topic: 8000 Issues (Dr Allis)
    Posted: 16 May 2020 at 11:06pm
The temp gauge needle went straight up and will not come down. I put on a new sending unit and still, it is at high noon. I also lost the rear work lights. Where is a good place to start checking for trouble. 
2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21909 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2020 at 1:05am
If the fuel gauge works, I'd guess it is the temp gauge itself. Would have to test wiring on the backside of the gauge to verify. Lights could be fuse or breaker depending on tractors age. Use Owners manual to see which style it has.
Back to Top
Michael V (NM) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: NM
Points: 2472 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Michael V (NM) Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2020 at 9:33am
I'm no help for the temp gauge. Have you replaced the light switch? not sure if that would be your problem tho,,,
I had some kind lighting issues with my 8010, there is an updated light switch/turn signal..
 
other than that,, well,, get a test light and start looking...corroded, dirty connecters can cause problems,  burned out bulbs??
Back to Top
Boss Man View Drop Down
Orange Level
Orange Level


Joined: 03 Mar 2018
Location: Greenleaf, WI
Points: 617 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Boss Man Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2020 at 10:21am
Look behind the dash for pinched or melted wires causing a short
Back to Top
Unit3 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 17 Oct 2009
Location: NC Iowa
Points: 5598 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Unit3 Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2020 at 12:47pm
Thank you all. I HATE when the lights don't work.
2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C
Back to Top
Krazy Karl View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2011
Location: SE MN
Points: 203 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Krazy Karl Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2020 at 8:04pm
If you unplug the temp sensor the gauge should peg one way then if you ground the wire it should peg the other way. Way to see if your gauge and wiring is ok. But if get nothing then have to figure out wire or gauge
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.090 seconds.


Help Support the
Unofficial Allis Forum