This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Rumely 6 oil pan
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
rumely6a View Drop Down
Bronze Level
Bronze Level


Joined: 17 Jun 2018
Location: Calgary alberta
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote rumely6a Quote  Post ReplyReply Direct Link To This Post Topic: Rumely 6 oil pan
    Posted: 17 Jun 2018 at 4:41am
after 30 years of collecting parts i am now putting together one or two Rumely 6 tractors

looking for the oil pan under the subframe. If you have one great. if you have one you don't want to sell I would like to get a pattern as I would have some made. thanks in advance


Edited by rumely6a - 17 Jun 2018 at 4:43am
Back to Top
Sponsored Links


Back to Top
Bill_MN View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Sioux Falls, SD
Points: 1471 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bill_MN Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2018 at 7:15am
Hi there, I am also working on a Rumely 6 (not mine) but I was just curious what carburetors you have for yours? I have an original Zenith 156 that is in bad shape and I'm looking to replace it with another model like a K5 that is easier to find parts for. What did you find? Thanks
1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow
Back to Top
rumely6a View Drop Down
Bronze Level
Bronze Level


Joined: 17 Jun 2018
Location: Calgary alberta
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote rumely6a Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2018 at 10:44am
I'll have a look and send photos. I believe one is a 156 but not certain.  

is your engine together?
Back to Top
Michael V (NM) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: NM
Points: 2467 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Michael V (NM) Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2018 at 7:00pm
I have a pair of fenders for a rumley6...
My granddad got them somewhere..some auction probably...I haven't really looked at them in quite some time, know they are for a rumley 6 cause I can kinda make out the decal on the fender,, or I could a few years ago,,here in dry NM they should be in decent shape..
Back to Top
rumely6a View Drop Down
Bronze Level
Bronze Level


Joined: 17 Jun 2018
Location: Calgary alberta
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote rumely6a Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2018 at 7:36pm
can you send or post photos?

I am negotiating to have sheetmetal made including fenders
Back to Top
rumely6a View Drop Down
Bronze Level
Bronze Level


Joined: 17 Jun 2018
Location: Calgary alberta
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote rumely6a Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2018 at 7:38pm
Bill in MN

both the carbs are Zenith but i don't have model numbers. I will be using both so not sure i can help at this time otherwise.

i can get the model numbers in a few weeks if that is helpful. i had these rebuilt in the 1990's when I started collecting parts.
Back to Top
Michael V (NM) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: NM
Points: 2467 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Michael V (NM) Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2018 at 9:15pm
Originally posted by rumely6a rumely6a wrote:

can you send or post photos?

I am negotiating to have sheetmetal made including fenders


Yes, be a day or three before I can get some...can also text pics..
Back to Top
rumely6a View Drop Down
Bronze Level
Bronze Level


Joined: 17 Jun 2018
Location: Calgary alberta
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote rumely6a Quote  Post ReplyReply Direct Link To This Post Posted: 18 Jun 2018 at 9:09am
Bill You might try Jim Treadwell at Treadwell Carb in NY 607- 963-6628

good guy
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.047 seconds.


Help Support the
Unofficial Allis Forum