| Author |
 Topic Search  Topic Options
|
2wise4agm 
Orange Level
Joined: 19 Aug 2011
Location: Smithton, MO
Points: 538
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: L2 harmonic balancer
Posted: 23 Jun 2015 at 6:41am |
|
The harmonic balancer on our L2 (426) is going bad. (The outside part has slipped on the inside piece.) I thought I remembered seeing some place that would rebuild them but I can't seem to find it. Anyone know?
|
 |
|
Sponsored Links
|
|
|
Adam Stratton
Orange Level Access
Joined: 11 Sep 2009
Location: SW MO
Points: 1363
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Jun 2015 at 7:19am |
http://hbrepair.com/harmonicbalancer_018.htm
This is where I sent mine off an L2. It was right around $200 to do the pulley I sent. I have no complaints and would use him again. Took a little over a week including shipping. The combine where the balancer went bad had been running hot, and I had hoped that maybe the pulley had been slipping before I knew it, and it would run cooler now, not the case, so I need to keep looking there....
|
|
2wise4agm
Orange Level
Joined: 19 Aug 2011
Location: Smithton, MO
Points: 538
|
Post Options
Thanks(0)
Quote Reply
Posted: 25 Jun 2015 at 8:13pm |
|
Thanks for the reply. Hopefully we'll finish up the fescue and wheat this week and I'll get it off and send it to them.
|
|
Mike Plotner
Orange Level
Joined: 02 Apr 2014
Location: Central Ohio
Points: 1577
|
Post Options
Thanks(0)
Quote Reply
Posted: 25 Jun 2015 at 8:27pm |
|
better replace it now, the one on my L2 kicked off last fall while shelling corn. when that goes the combine just stops. I didn't have time to send it off to get it fixed right and there is none to be found in any salvage yards within a few hundred miles. I just used a harmonic balancer off a 7045 and it works fine
|
|
2001 Gleaner R42, 1978 7060, 1977 7000, 1966 190 XT, 1966 D-17 Series IV and 1952 WD and more keep my farm running!
|
|
ranger42
Orange Level
Joined: 14 Mar 2011
Points: 420
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jun 2015 at 8:30am |
 2wise4agm wrote:
The harmonic balancer on our L2 (426) is going bad. (The outside part has slipped on the inside piece.) I thought I remembered seeing some place that would rebuild them but I can't seem to find it. Anyone know? |
What were the symptoms of it slipping? Just curious because I have always been paranoid about the one on the 210 slipping.
|
|
2wise4agm
Orange Level
Joined: 19 Aug 2011
Location: Smithton, MO
Points: 538
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jun 2015 at 8:34am |
|
I had the injection pump rebuilt and the timing marks weren't even close to being lined up when I went to remove the pump.
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8629
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jun 2015 at 9:50am |
Adam Stratton wrote:
http://hbrepair.com/harmonicbalancer_018.htm
This is where I sent mine off an L2. It was right around $200 to do the pulley I sent. I have no complaints and would use him again. Took a little over a week including shipping. The combine where the balancer went bad had been running hot, and I had hoped that maybe the pulley had been slipping before I knew it, and it would run cooler now, not the case, so I need to keep looking there.... |
Make sure you check your guage /sender against a know accurate one.
|
|
