| Author |
 Topic Search  Topic Options
|
troy31 
Bronze Level
Joined: 04 Feb 2017
Location: ky
Points: 16
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: h3 gas engine?
Posted: 05 Feb 2017 at 8:32pm |
|
Anyone know we're to get a rebuild kit for a h3 gas crawler for a.good.price or were to get a complete motor to go in a h3 used or new.that's in good shape.. iv heard they have same.motor.as a d15 farm tractor but is it.a 149 or a 160 in the crawler
|
 |
|
Sponsored Links
|
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7484
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Feb 2017 at 8:40pm |
|
Both were used. Early models had the 149, later models had the 160. If it has an oil bath air cleaner, chances are it's a 149. The model and serial number is stamped on a flat surface close to the exhaust manifold near the back of the engine.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
Eric B
Orange Level
Joined: 09 Feb 2012
Location: British Columbi
Points: 967
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Feb 2017 at 2:10pm |
|
Overhaul kits are easy to get from dealers on this site and elsewhere too.
|
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
Tracy Martin TN
Orange Level Access
Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10752
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Feb 2017 at 3:11pm |
|
If it is a 160 cid, hold on to your wallet! HTH Tracy
|
|
No greater gift than healthy grandkids!
|
|
troy31
Bronze Level
Joined: 04 Feb 2017
Location: ky
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Feb 2017 at 9:37am |
|
My only numbers on the block is 3-2987-r. Least it looks like a 3 at the beganing
|
|
nevans
Orange Level
Joined: 06 Dec 2011
Location: Red Bud. IL
Points: 837
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Feb 2017 at 2:59pm |
|
we have one that was overhauled nephew was going to put it in a b for pulling its a 160 will take 1750 Niel
|
|
Eric B
Orange Level
Joined: 09 Feb 2012
Location: British Columbi
Points: 967
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Feb 2017 at 5:40pm |
 troy31 wrote:
My only numbers on the block is 3-2987-r. Least it looks like a 3 at the beganing |
I'm not disputing your findings but sometimes you have to wire brush and/or use a sandpaper in order to get all the digits showing...
|
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
troy31
Bronze Level
Joined: 04 Feb 2017
Location: ky
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Feb 2017 at 6:41pm |
|
I cleaned it off good and that's the numbers...also noticed there is no fuel pump or place.for.one..so this is a.tractor motor, but can someone tell me what kind so I can get a rebuild kit
|
|
Eric B
Orange Level
Joined: 09 Feb 2012
Location: British Columbi
Points: 967
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Feb 2017 at 7:35pm |
troy31 wrote:
I cleaned it off good and that's the numbers...also noticed there is no fuel pump or place.for.one..so this is a.tractor motor, but can someone tell me what kind so I can get a rebuild kit
|
If those are all the digits you have, you will likely have to pull the head to get the cubic inch or else ordering parts would be a leap in the dark. I have two D14's with the same looking block as you have and the row of digits start with "149" and a group of five numbers plus R at the end which has to do with compression ratio apparently. It's maybe more likely that you have a 149, however, you're really lucky if you have a 160...more sought after but way more for parts cost.
|
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
JoeO(CMO)
Orange Level
Joined: 11 Sep 2009
Location: Cent Missouri
Points: 2696
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Feb 2017 at 9:39am |
troy31 wrote:
My only numbers on the block is 3-2987-r. Least it looks like a 3 at the beganing |
Probably 3 since it is a H3 with the serial. Could be looking at a 5 possibly which could have a 1 in front of it.
Edited by JoeO(CMO) - 10 Feb 2017 at 9:44am
|
|
|
|
Calvin Schmidt
Orange Level
Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4533
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Feb 2017 at 2:07pm |
I checked the dealers parts book and H-3's serial # 6959 and lower had the 149 engine.
Serial 6959 and higher had the 160 engine. Serial number on the left side of the torque tube where the engine bolts to the torque tube.
|
|
Nothing is impossible if it is properly financed
|
|
troy31
Bronze Level
Joined: 04 Feb 2017
Location: ky
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2017 at 2:12am |
|
This number is right on the block, same side as carb, toward the back...I'd show a photo but it won't let me upload from my phone, the engine ain't orginal cuz it does not have a fuel pump
|
|
Kipn
Orange Level
Joined: 12 Sep 2009
Location: Tewksbury, Ma
Points: 800
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 May 2017 at 6:57am |
|
Due to serial number, its a 149. It probabaly has an H in front of the 3, if it came out of a dozer.
|
|
1961 H3
|
|
pinball
Orange Level Access
Joined: 28 May 2014
Location: missouriu
Points: 6365
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 May 2017 at 12:21pm |
|
Are you sure there is not a fuel pump. Never seen a gas motor with out one originally. Could it be the fuel pump went bad and removed and a plate put over it and they just used the pressure from the fuel tank. Just curious I guess. norm
|
|
