h3 gas engine?
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Construction and other equipment
Forum Description: everything else with orange (or yellow) paint
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=134709
Printed Date: 04 Jun 2024 at 5:11pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: h3 gas engine?
Posted By: troy31
Subject: h3 gas engine?
Date Posted: 05 Feb 2017 at 8:32pm
| Anyone know we're to get a rebuild kit for a h3 gas crawler for a.good.price or were to get a complete motor to go in a h3 used or new.that's in good shape.. iv heard they have same.motor.as a d15 farm tractor but is it.a 149 or a 160 in the crawler |
Replies:
Posted By: DSeries4
Date Posted: 05 Feb 2017 at 8:40pm
|
Both were used. Early models had the 149, later models had the 160. If it has an oil bath air cleaner, chances are it's a 149. The model and serial number is stamped on a flat surface close to the exhaust manifold near the back of the engine. ------------- '49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080 |
Posted By: Eric B
Date Posted: 06 Feb 2017 at 2:10pm
|
Overhaul kits are easy to get from dealers on this site and elsewhere too. ------------- Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal! |
Posted By: Tracy Martin TN
Date Posted: 06 Feb 2017 at 3:11pm
|
If it is a 160 cid, hold on to your wallet! HTH Tracy ------------- No greater gift than healthy grandkids! |
Posted By: troy31
Date Posted: 07 Feb 2017 at 9:37am
| My only numbers on the block is 3-2987-r. Least it looks like a 3 at the beganing |
Posted By: nevans
Date Posted: 07 Feb 2017 at 2:59pm
| we have one that was overhauled nephew was going to put it in a b for pulling its a 160 will take 1750 Niel |
Posted By: Eric B
Date Posted: 07 Feb 2017 at 5:40pm
I'm not disputing your findings but sometimes you have to wire brush and/or use a sandpaper in order to get all the digits showing... ------------- Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal! |
troy31 wrote:Posted By: troy31
Date Posted: 08 Feb 2017 at 6:41pm
|
I cleaned it off good and that's the numbers...also noticed there is no fuel pump or place.for.one..so this is a.tractor motor, but can someone tell me what kind so I can get a rebuild kit |
Posted By: Eric B
Date Posted: 08 Feb 2017 at 7:35pm
If those are all the digits you have, you will likely have to pull the head to get the cubic inch or else ordering parts would be a leap in the dark. I have two D14's with the same looking block as you have and the row of digits start with "149" and a group of five numbers plus R at the end which has to do with compression ratio apparently. It's maybe more likely that you have a 149, however, you're really lucky if you have a 160...more sought after but way more for parts cost. ------------- Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal! |
Posted By: JoeO(CMO)
Date Posted: 10 Feb 2017 at 9:39am
Probably 3 since it is a H3 with the serial. Could be looking at a 5 possibly which could have a 1 in front of it. ------------- |
Posted By: Calvin Schmidt
Date Posted: 10 Feb 2017 at 2:07pm
|
I checked the dealers parts book and H-3's serial # 6959 and lower had the 149 engine.
Serial 6959 and higher had the 160 engine. Serial number on the left side of the torque tube where the engine bolts to the torque tube. ------------- Nothing is impossible if it is properly financed |
Posted By: troy31
Date Posted: 11 Feb 2017 at 2:12am
|
This number is right on the block, same side as carb, toward the back...I'd show a photo but it won't let me upload from my phone, the engine ain't orginal cuz it does not have a fuel pump |
Posted By: Kipn
Date Posted: 13 May 2017 at 6:57am
|
Due to serial number, its a 149. It probabaly has an H in front of the 3, if it came out of a dozer. ------------- 1961 H3 |
Posted By: pinball
Date Posted: 13 May 2017 at 12:21pm
| Are you sure there is not a fuel pump. Never seen a gas motor with out one originally. Could it be the fuel pump went bad and removed and a plate put over it and they just used the pressure from the fuel tank. Just curious I guess. norm |