This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Carbs same on C and CA? |
Post Reply |
Author | |
Hubnut
Orange Level Joined: 30 Jul 2014 Location: Gainesville, FL Points: 1812 |
Post Options
Thanks(0)
Posted: 26 Mar 2016 at 4:39pm |
Are the carburetors for the C and CA identical?
|
|
1940 B "Lucy"
1941 B w/ Woods L59 "Flavia" 1942 B w/ finish mower "Dick" 1941 C w/ 3-point "Maggie" 1947 C SFW w/ L306 "Trixie" 1972 314H |
|
Sponsored Links | |
Leon n/c AR.
Bronze Level Joined: 19 Mar 2013 Location: Heber Springs A Points: 168 |
Post Options
Thanks(0)
|
B-C-CA carbs will interchange whether Zenith or Marvell-Schebler brand. Leon
|
|
Dick L
Orange Level Joined: 12 Sep 2009 Location: Edon Ohio Points: 5082 |
Post Options
Thanks(0)
|
They were not! As stated above they are interchangeable.
|
|
Hubnut
Orange Level Joined: 30 Jul 2014 Location: Gainesville, FL Points: 1812 |
Post Options
Thanks(0)
|
Dick,
I take it they were different from factory, but would all work despite the tractor model? Thanks. Steve |
|
1940 B "Lucy"
1941 B w/ Woods L59 "Flavia" 1942 B w/ finish mower "Dick" 1941 C w/ 3-point "Maggie" 1947 C SFW w/ L306 "Trixie" 1972 314H |
|
Steve in NJ
Orange Level Access Joined: 12 Sep 2009 Location: Andover, NJ Points: 11550 |
Post Options
Thanks(0)
|
The B/C Zenith carbs were in the same family, but when it came to the CA, they had a different carb on them because of the higher rpm range they worked in. They will all interchange, but the CA carb on a B or C might be a tick on the fat side for the fuel ratio because of the different jetting...
Steve@B&B |
|
39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife
|
|
Dick L
Orange Level Joined: 12 Sep 2009 Location: Edon Ohio Points: 5082 |
Post Options
Thanks(0)
|
Assuming all models have been upgraded. If you have a low compression 3 1/4" piston engine the carburetor from a CA might not start well with the larger venturi. |
|
wfmurray
Orange Level Joined: 13 Sep 2009 Location: Bostic NC Points: 1225 |
Post Options
Thanks(0)
|
I got a 49 b to restore and the carb was bad. It did't have a venture.Got one off a C A and bolt holes was wider about one fourth inch .Filed it out to fit .Cranks real good but wants to surg when not pulling a load.
|
|
Hubnut
Orange Level Joined: 30 Jul 2014 Location: Gainesville, FL Points: 1812 |
Post Options
Thanks(0)
|
Thanks everyone. Do you know the maker of the carb for the CA? Still a Zenith?
|
|
1940 B "Lucy"
1941 B w/ Woods L59 "Flavia" 1942 B w/ finish mower "Dick" 1941 C w/ 3-point "Maggie" 1947 C SFW w/ L306 "Trixie" 1972 314H |
|
norm[ind]
Orange Level Joined: 29 Oct 2010 Location: bourbon,ind Points: 2992 |
Post Options
Thanks(0)
|
does yours have a surge spring on it --yes or no if surging
|
|
wfmurray
Orange Level Joined: 13 Sep 2009 Location: Bostic NC Points: 1225 |
Post Options
Thanks(0)
|
It has a surg spring
|
|
Alex09(WI)
Orange Level Joined: 15 Mar 2012 Location: CECIL WI Points: 1698 |
Post Options
Thanks(0)
|
Not sure with the zenith, but the Marvel Schebler is TSX154 for b/c/ca. Tractors came with both Zenith and M-S depending on what the factory had on hand at the time. |
|
www.awtractor.com
A&W TRACTOR 920-598-1287 KEEPING ALLIS-CHALMERS IN THE FIELDS THROUGH THE 21ST CENTURY |
|
Dick L
Orange Level Joined: 12 Sep 2009 Location: Edon Ohio Points: 5082 |
Post Options
Thanks(0)
|
Any that I run across had the Marvell-Schebler
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |