This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Wheel eccentric adjustment tool
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
JoeO(CMO) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Cent Missouri
Points: 2696 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JoeO(CMO) Quote  Post ReplyReply Direct Link To This Post Topic: Wheel eccentric adjustment tool
    Posted: 17 Aug 2011 at 5:20pm
Some time back someone posted about an adjustment tool for the square drive eccentric for CA, D10 and D12.  I searched and couldn't find a reference to the tool.  I think it was availabe from a tool company but don't recall which one.




Back to Top
Sponsored Links


Back to Top
wkpoor View Drop Down
Orange Level
Orange Level


Joined: 25 Apr 2010
Location: Amanda, OH
Points: 825 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wkpoor Quote  Post ReplyReply Direct Link To This Post Posted: 17 Aug 2011 at 6:35pm
I remember the thread too but not the specifics. I just use a square drive socket and breaker bar.
Back to Top
JoeO(CMO) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Cent Missouri
Points: 2696 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JoeO(CMO) Quote  Post ReplyReply Direct Link To This Post Posted: 17 Aug 2011 at 7:15pm
The CA, D10 and D12 had 1/2 inch square, which is a little tough to find a square drive-driven as compared to other eccentrics had a hex head where a standard socket could be used.




Back to Top
amac View Drop Down
Silver Level
Silver Level


Joined: 11 Nov 2010
Location: Kalona, IA
Points: 251 		Post Options Post Options   Thanks (0) Thanks(0)   Quote amac Quote  Post ReplyReply Direct Link To This Post Posted: 17 Aug 2011 at 7:56pm
take two 1/2" drive impact sockets and weld them together so you have a square 1/2" on both ends. By using an impact wrench there is less of a chance of twisting them off.
Back to Top
BobDinNC View Drop Down
Silver Level
Silver Level
Avatar

Joined: 13 Sep 2009
Location: Newport, NC
Points: 251 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BobDinNC Quote  Post ReplyReply Direct Link To This Post Posted: 17 Aug 2011 at 9:52pm
Thanks, AMC.  I would never have thought of that.
Back to Top
GregLawlerMinn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Lawler, Mn
Points: 1226 		Post Options Post Options   Thanks (0) Thanks(0)   Quote GregLawlerMinn Quote  Post ReplyReply Direct Link To This Post Posted: 17 Aug 2011 at 9:55pm
Or you could use a 1/2" impact extension, a hammer, and a big cresent wrench. I use a good 8 pt 1/2 socket on a 1/2" drive for my CA's.
What this country needs is more unemployed politicians-and lawyers.
Currently have: 1 D14 and a D15S2.
With new owners: 2Bs,9CAs,1WD,2 D12s,5D14s,3D15S2s, 2D17SIVs,D17D,1D19D;1 Unstyled WC
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.082 seconds.


Help Support the
Unofficial Allis Forum