This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Coggonobrien's D15 Series III |
Post Reply | Page 123 4> |
Author | |
AndrewGubbels
Orange Level Joined: 12 Sep 2009 Location: nebraska Points: 1486 |
Post Options
Thanks(0)
Posted: 10 Mar 2021 at 4:44am |
Looks like a great project!! Well done!!
|
|
Andrew Gubbels
Gubbels Restoration |
|
Sponsored Links | |
IBWD MIke
Orange Level Joined: 08 Apr 2012 Location: Newton Ia. Points: 3448 |
Post Options
Thanks(0)
|
Like!
|
|
Strokendiesel002
Silver Level Joined: 04 Apr 2019 Location: 53158 Points: 252 |
Post Options
Thanks(0)
|
Looking sharp!
|
|
plummerscarin
Orange Level Access Joined: 22 Jun 2015 Location: ia Points: 3128 |
Post Options
Thanks(0)
|
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Mounted, ready for a drive an retorque. 59.75 center to center.
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Rims are new from wold. 15" wide for 16.9x26
|
|
plummerscarin
Orange Level Access Joined: 22 Jun 2015 Location: ia Points: 3128 |
Post Options
Thanks(0)
|
Looking good. Yes progress can be slow. Are rims new? Fits 16.9-28?
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Slow progress
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
I won't be changing or modifying them. If it was a concern I would careful bend them to spread them. As they are now I can run them just fine.
Edited by coggonobrien - 19 Feb 2021 at 11:31am |
|
JayIN
Orange Level Joined: 18 Dec 2009 Location: SE/IN Points: 1982 |
Post Options
Thanks(0)
|
Hell, I would just screw on a 2" extension onto the middle lever and be done with it. That should make it easier to find with mittens on.
|
|
sometimes I walk out to my shop and look around and think "Who's the idiot that owns this place?"
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
G,
Tractor doesn't do much during the winter. The hydraulics are used for a deere barge box and a heston 1091 haybine. The Dr is right, after tires are done I need to fabricate a 3pt adapter similar to his. |
|
allischalmerguy
Orange Level Joined: 11 Sep 2009 Location: Deep River, IA Points: 2864 |
Post Options
Thanks(0)
|
Tom,
I wish I had half your mechanical/fabricating skills! Well done! Pastor Mike |
|
It is great being a disciple of Jesus! 1950 WD, 1957 D17...retired in Iowa,
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19518 |
Post Options
Thanks(0)
|
The custom live hydraulic system has been thru the summers of 2017-18-19 and 2020. It has never once failed to prime, which was my only concern with the pump mounted up as high as it is. It has worked well with no issues and makes the tractor very universal with modern hydraulics. Now maybe someday we can fabricate a real nice/heavy Category #2 three-point hitch that can easily be converted back to snap-coupler.
|
|
Gary
Orange Level Access Joined: 13 Sep 2009 Location: Peterborough,On Points: 5171 |
Post Options
Thanks(0)
|
Coggon Have you had an opportunity to use the R/H 3 Hydraulic Levers on your Ser.III while working outdoors in this extreme cold and wearing a pair of insulated mitts ? I think you will find it is a bit awkward. I did a similar revision to my D-12 Ser.III for the 2 R/H Valves. I mounted a Meyers 7' Snow Blade for winter Snow Plowing. The shorter inner lever is for Hydraulic Angle, longer outer lever for raise, lower. Both valve levers are similar to yours, close together, point straight up. It is a royal pain to use the inner hydraulic angle lever on a repetitive basis. I angle plow to only one side of my driveway, so I have to change the angle from right to left and vise versa at the end of each pass. Wearing a pair of insulated mitts, it's rather difficult. I need to rework these levers. G |
|
JayIN
Orange Level Joined: 18 Dec 2009 Location: SE/IN Points: 1982 |
Post Options
Thanks(0)
|
Fun to watch on a winter day!
|
|
sometimes I walk out to my shop and look around and think "Who's the idiot that owns this place?"
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Pictures coming. Putting new shoes on the rear
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Dan73
Orange Level Joined: 04 Jun 2015 Location: United States Points: 6054 |
Post Options
Thanks(0)
|
The pictures sure do look great. Joe just find a big rock to put in the backhoe bucket and extend it out a little she will turn like the front end is floating on air |
|
desertjoe
Orange Level Access Joined: 23 Sep 2013 Location: New mexico Points: 13358 |
Post Options
Thanks(0)
|
Hey Coggin,,,Them right there are some great pics,,,especially the one with the Series II with the sun coming up behind it,,,good enough for a calendar shot,,,,,, Me thinks you might need another barn,,,,, sure wisht the power steering worked that good on my tractor,,,,, Edited by desertjoe - 25 Apr 2017 at 1:01pm |
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
If a 3 pto happens we will build it. The factory one is too cheaply built for my taste
|
|
Unit3
Orange Level Joined: 17 Oct 2009 Location: NC Iowa Points: 5497 |
Post Options
Thanks(0)
|
Will there be a factory 3 point on it someday? It is SO COOL!!! Time well spent. A1, top self, and high marks for you.
|
|
2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
desertjoe
Orange Level Access Joined: 23 Sep 2013 Location: New mexico Points: 13358 |
Post Options
Thanks(0)
|
Hey Coggin,,,,Now,, that is sure lookin great,,,!!! but you KNOW,,,you is goin to have to go all the way and get you a claw hammer and a brick and straighten thet left fender,,,,,,,,,,,,,,,and,,,is a complete paint job in your plans for this tractor,,?? Looking Good,,Guy,,,lookin good,,,,!!!! |
|
allischalmerguy
Orange Level Joined: 11 Sep 2009 Location: Deep River, IA Points: 2864 |
Post Options
Thanks(0)
|
What a neat working tractor you are going to have when you get this all done!
Thanks for sharing your progress. It is amazing to watch people fabricate and build and make things work! It is beyond my ability. I am just amazed at you guys! Pastor Mike Townsley |
|
It is great being a disciple of Jesus! 1950 WD, 1957 D17...retired in Iowa,
|
|
JoeO(CMO)
Orange Level Joined: 11 Sep 2009 Location: Cent Missouri Points: 2694 |
Post Options
Thanks(0)
|
Looking Good!!
|
|
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Greg_WJP_(WI)
Silver Level Access Joined: 27 Sep 2009 Location: W.Central, WI Points: 250 |
Post Options
Thanks(0)
|
It looks better than good!!!
|
|
coggonobrien
Orange Level Access Joined: 14 Nov 2010 Location: Eastern Iowa Points: 1806 |
Post Options
Thanks(0)
|
Doc has most of the talent, I just have modern technology making me look good on the fabrication end
|
|
Post Reply | Page 123 4> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |