This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


WD Hydraulics
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
KC/WD View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 03 Nov 2009
Location: Kansas City
Points: 81 		Post Options Post Options   Thanks (0) Thanks(0)   Quote KC/WD Quote  Post ReplyReply Direct Link To This Post Topic: WD Hydraulics
    Posted: 27 Jan 2010 at 3:31pm
I think I'll treat my WD to fresh hydraulic fluid, she deserves it!
What is her capacity, 5 glns?
 
Thanks,
KC
Back to Top
Sponsored Links


Back to Top
omahagreg View Drop Down
Orange Level Access
Orange Level Access


Joined: 11 Sep 2009
Location: Omaha, Nebraska
Points: 2806 		Post Options Post Options   Thanks (0) Thanks(0)   Quote omahagreg Quote  Post ReplyReply Direct Link To This Post Posted: 27 Jan 2010 at 3:56pm
Hydraulic pump says 5 Quarts.
Greg Kroeker
1950 WD with wide front and Freeman trip loader
Back to Top
roughstock View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Jan 2010
Location: Michigan
Points: 690 		Post Options Post Options   Thanks (0) Thanks(0)   Quote roughstock Quote  Post ReplyReply Direct Link To This Post Posted: 27 Jan 2010 at 6:24pm
I hope your fluid change goes better than mine did. I ended up using two gallons after a line to my loader blew.
Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8573 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 27 Jan 2010 at 10:31pm
It ain't much but 5qt seems like too little.Been a while. Just be sure to check it as full with lift arms up and engine off.Wipe the dipstick off and re-insert for accurate reading.You can check it before startup but oil will read higher on the stick before you wipe it off which can make you think it's got enough when you don't.
Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8573 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 27 Jan 2010 at 10:33pm
Also pull the little pipe plug at the bottom of the control hsg to drain it all.
Back to Top
Brian G. NY View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: 12194
Points: 2259 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Brian G. NY Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2010 at 10:36am
My WD-45 Owners Manual says 6 Qts.
I also advise doing what Steve M. says; there may be a bit of sludge in there.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.066 seconds.


Help Support the
Unofficial Allis Forum