This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


185 power director
 Post Reply Post Reply
Author
Message
 Rating: Topic Rating: 1 Votes, Average 5.00  Topic Search Topic Search  Topic Options Topic Options
grinder220 View Drop Down
Orange Level
Orange Level


Joined: 11 Jan 2012
Location: Clinton Iowa
Points: 2370 		Post Options Post Options   Thanks (0) Thanks(0)   Quote grinder220 Quote  Post ReplyReply Direct Link To This Post Topic: 185 power director
    Posted: 13 May 2023 at 9:59pm
Should I be able to blow air out the hole in the bottom of the housing that has the transmission input shaft seal when hooking air up to the pressure lines? I tried it once with the original steel rings on it and then with another set, both times I had air blowing out that hole. I don't want to put it back together if something needs attention there.
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21866 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2023 at 5:55am
That bearing retainer casting is new?? or you're trying to reuse it ?? 
Back to Top
grinder220 View Drop Down
Orange Level
Orange Level


Joined: 11 Jan 2012
Location: Clinton Iowa
Points: 2370 		Post Options Post Options   Thanks (0) Thanks(0)   Quote grinder220 Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2023 at 7:09am
Reusing the original
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21866 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2023 at 7:13am
Generally.....a BAD idea. It's not an air tight connection, but they always have some wear inside where the sealing rings go and if it is re-used, it will never run as many hours as a new one. Be sure the oil seal isn't pressed clear into the bottom....only flush at the top.

Edited by DrAllis - 14 May 2023 at 7:18am
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2023 at 9:04pm
If there is much ware in housing, it will start breaking ends off sealing rings.                            MACK
Back to Top
grinder220 View Drop Down
Orange Level
Orange Level


Joined: 11 Jan 2012
Location: Clinton Iowa
Points: 2370 		Post Options Post Options   Thanks (0) Thanks(0)   Quote grinder220 Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2023 at 9:29pm
I had another one on a shelf with very little wear that I swapped out. I assume they are a smooth bore when new? This one still leaked some air but no where near as bad as the original.
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21866 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2023 at 9:48pm
Absolutely a straight thru hole when new.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.030 seconds.


Help Support the
Unofficial Allis Forum