This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D19 gas motor to D17 diesel |
Post Reply |
Author | |
HD6GTOM
Orange Level Joined: 30 Nov 2009 Location: MADISON CO IA Points: 6627 |
Post Options
Thanks(0)
Posted: 04 Oct 2020 at 8:22pm |
Is it a simple job to put a D19 gas into a series 4 that had a bad motor. Sorry if its been asked before. Old guy has a D19 with bad rear end or tranny he doesn't know which. Good motor. Will it bolt into his D17? They are both complete units. D17 tossed a rod thru the block got into the water jacket. I get to look at it next week if he feels good.
|
|
Sponsored Links | |
DiyDave
Orange Level Access Joined: 11 Sep 2009 Location: Gambrills, MD Points: 50762 |
Post Options
Thanks(0)
|
It has been done, but the sheet metal won't fit, IIRR. I don't envy you in this job...
|
|
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
|
|
HD6GTOM
Orange Level Joined: 30 Nov 2009 Location: MADISON CO IA Points: 6627 |
Post Options
Thanks(0)
|
Ok, probably pass on it. Thanks
|
|
desertjoe
Orange Level Access Joined: 23 Sep 2013 Location: New mexico Points: 13365 |
Post Options
Thanks(0)
|
Hey Tom,,,where is your adventurous spirit,,,? You do have a cuttin torch and a welder don't you,,,? Just think how much your neighbor will love you for bailing him out,,,,,,,,
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8070 |
Post Options
Thanks(0)
|
Your title says 17 diesel...of so I don't see the challenge. Gasser would be different story.
|
|
HD6GTOM
Orange Level Joined: 30 Nov 2009 Location: MADISON CO IA Points: 6627 |
Post Options
Thanks(0)
|
Wondering about it. I know my Diesel 17 was longer than the gas units. Was hoping it would be a simple bolt up. The D19 tin is good, rad is good. Could all tin be switched,?
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8070 |
Post Options
Thanks(0)
|
I'm thinking direct bolt in. May have to use clutch and flywheel from 17 but it should bolt to crank ok. PM the Dr. He will know. The engines are same physical dementions.
19 is wider I think so tin will not swap. Edited by SteveM C/IL - 07 Oct 2020 at 11:46am |
|
Gary in da UP
Orange Level Joined: 13 Sep 2009 Location: EUP of Mi. Points: 1885 |
Post Options
Thanks(0)
|
I repowered a wc with a 262 gas 6 cyl needs little to be considered done will be an awesome puller or tractor rider for sale due to health reasons send pm for more info
Edited by Gary in da UP - 10 Oct 2020 at 9:03am |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |