This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Muffler Install
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
cjallis View Drop Down
Silver Level
Silver Level
Avatar

Joined: 13 Jun 2013
Location: Sheboygan
Points: 87 		Post Options Post Options   Thanks (0) Thanks(0)   Quote cjallis Quote  Post ReplyReply Direct Link To This Post Topic: Muffler Install
    Posted: 09 Apr 2018 at 6:39pm
Can anyone tell me what goes through the manifold and muffler to hold it in place from moving? There is a hole in the top of the manifold where the muffler attaches but it does not go all the way through manifold. 
Thanks,
Carl
Back to Top
Sponsored Links


Back to Top
Larry in NC View Drop Down
Orange Level
Orange Level


Joined: 09 Feb 2016
Location: NC
Points: 1050 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Larry in NC Quote  Post ReplyReply Direct Link To This Post Posted: 09 Apr 2018 at 7:01pm
You did not say what tractor you are putting the muffler on, but the hole on the manifold is normally there to bolt through the flange on the muffler if the hole does not go all the way through the manifold. 
Back to Top
cjallis View Drop Down
Silver Level
Silver Level
Avatar

Joined: 13 Jun 2013
Location: Sheboygan
Points: 87 		Post Options Post Options   Thanks (0) Thanks(0)   Quote cjallis Quote  Post ReplyReply Direct Link To This Post Posted: 09 Apr 2018 at 8:34pm
It's on a C! Ok yes I thought so. 
Back to Top
DSeries4 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7462 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DSeries4 Quote  Post ReplyReply Direct Link To This Post Posted: 10 Apr 2018 at 7:33pm
There are supposed to be 2 holes on the side of the manifold.  The one you can't see is probably broken off and rusted.  It will need to get drilled out and the hole re-tapped.  Best to run the tap through the other hole too.    For bolts, use brass bolts only.  The one that does not go through the manifold will need to be cut shorter.
This is on my WD45 ...
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29792 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 11 Apr 2018 at 6:18am
I believe a C would have only one bolt vs two on a WD45.
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.109 seconds.


Help Support the
Unofficial Allis Forum