![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Update on 7060 PD Trans Issues |
Post Reply ![]() |
Author | |
KevinON ![]() Orange Level ![]() Joined: 07 Dec 2009 Location: Schomberg, ON Points: 801 |
![]() ![]() ![]() ![]() ![]() Posted: 11 Jul 2012 at 9:00pm |
Well I changed the tranny filter and cleaned out the suction screen which wasn't very dirty. I filled with fresh oil. The old oil looked good on the dipstick, but when pouring out in the light it looked dirty. I installed a pressure guage at the filter sending unit, and at idle it produced close to 30psi, and at high idle it produced over 60 psi. The tractor is now functioning again. The only issue it has is there is a hesitation for a few seconds when taking off in 5th gear, high range, low PD. Is this normal, or do I have some upcoming PD issues?? Thanks so much for the help, Dr. Allis and MACK, along with others!
|
|
![]() |
|
Sponsored Links | |
![]() |
|
DrAllis ![]() Orange Level Access ![]() Joined: 12 Sep 2009 Points: 21914 |
![]() ![]() ![]() ![]() ![]() |
On top of the Power Director valve there is a round plug that takes an allen wrench to remove. Remove this plug and use it to procure a fitting that will fit that hole and get a pressure gauge/hose and check the pressures at full throttle and hot oil....should be 195-205 psi.....by "hot" I mean in the field for an hour or drive it down the road for an hour at top speed. If pressures are acceptable, you may simply have a PD clutch that needs to be resealed and freshened up a bit.
|
|
![]() |
|
MACK ![]() Orange Level ![]() Joined: 17 Nov 2009 Points: 7664 |
![]() ![]() ![]() ![]() ![]() |
Could also have the torque limiter slipping when you take off in 5th. MACK
|
|
![]() |
|
KevinON ![]() Orange Level ![]() Joined: 07 Dec 2009 Location: Schomberg, ON Points: 801 |
![]() ![]() ![]() ![]() ![]() |
Thanks, guys. I will do that when I have a chance! I had thought of the torque limiter as well.
|
|
![]() |
|
michaelwis ![]() Orange Level ![]() ![]() Joined: 12 Sep 2009 Location: Wi Points: 8765 |
![]() ![]() ![]() ![]() ![]() |
Sounds to me like torque limiter also . My 7040 had hesitation now and then .. fixed the torque limiter , problem solved ...
|
|
WD WD45 DIESEL D 14 D-15 SERIES 2 190XT TERRA TIGER ac allcrop 60 GLEANER F 6060 7040.and attachments for all Proud to be an active farmer
|
|
![]() |
|
KevinON ![]() Orange Level ![]() Joined: 07 Dec 2009 Location: Schomberg, ON Points: 801 |
![]() ![]() ![]() ![]() ![]() |
Thanks, Michael!
|
|
![]() |
|
michaelwis ![]() Orange Level ![]() ![]() Joined: 12 Sep 2009 Location: Wi Points: 8765 |
![]() ![]() ![]() ![]() ![]() |
Kevin .. there are ways to fix it w o ....a full blown AC (AGCO ) REPAIR KIT .....
|
|
WD WD45 DIESEL D 14 D-15 SERIES 2 190XT TERRA TIGER ac allcrop 60 GLEANER F 6060 7040.and attachments for all Proud to be an active farmer
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |