![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D 15 clutch |
Post Reply ![]() |
Author | |
ACinSC ![]() Orange Level ![]() Joined: 16 Dec 2015 Location: South Carolina Points: 2994 |
![]() ![]() ![]() ![]() ![]() Posted: 06 Jun 2020 at 8:37am |
Have a pretty bad engine rear main seal leak . Would this cause the clutch to be grabby ? Mostly leaks at WOT . THANKS!!
|
|
![]() |
|
Sponsored Links | |
![]() |
|
Tracy Martin TN ![]() Orange Level Access ![]() Joined: 11 Sep 2009 Location: Gallatin,TN Points: 10794 |
![]() ![]() ![]() ![]() ![]() |
Yes it can cause it to be sticky. Also cause it to slip under a load. Best to split at engine, replace rear main seal, tranny input seal, throw out bearing, and clutch and pressure plate from Rick Corder. Then good to go! HTH Tracy
Edited by Tracy Martin TN - 06 Jun 2020 at 9:42am |
|
No greater gift than healthy grandkids!
|
|
![]() |
|
ACinSC ![]() Orange Level ![]() Joined: 16 Dec 2015 Location: South Carolina Points: 2994 |
![]() ![]() ![]() ![]() ![]() |
Thanks Tracy , I was wondering if the rear main seal and clutch could be done at the same time . My favorite son does have splitting stands now .
|
|
![]() |
|
Rick ![]() Orange Level ![]() ![]() Joined: 11 Sep 2009 Location: Jonesburg,Mo. Points: 3698 |
![]() ![]() ![]() ![]() ![]() |
I can fix you up AC with the clutch unit and bearing...Rick
|
|
![]() |
|
ACinSC ![]() Orange Level ![]() Joined: 16 Dec 2015 Location: South Carolina Points: 2994 |
![]() ![]() ![]() ![]() ![]() |
Yeah Rick . My favorite son got his clutch and brakes from you . Thanks !
|
|
![]() |
|
DSeries4 ![]() Orange Level ![]() ![]() Joined: 12 Sep 2009 Location: Ontario, Canada Points: 7505 |
![]() ![]() ![]() ![]() ![]() |
Yes! You will have to remove the oil pan as well to position the rear seal properly. |
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '63 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
![]() |
|
ACinSC ![]() Orange Level ![]() Joined: 16 Dec 2015 Location: South Carolina Points: 2994 |
![]() ![]() ![]() ![]() ![]() |
Was wondering about the oil pan . It was off when I got this tractor . Quite the job to get the back bolts in IIRR . Might be easier to just pull the motor ? Thanks
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |