| Author |
 Topic Search  Topic Options
|
allismanamp 
Orange Level
Joined: 15 Oct 2011
Location: MN
Points: 665
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: anyone know?
Posted: 02 Jun 2012 at 10:29pm |
were i can get a new oil breather bowl for my allis chalmers c engine i was cleaning mine out today and held it up to the light only to see little pin holes where it has rotted out. should i just tuck a k&n oil air filter in the pipe under the hood off the breather? also do the original breathers really do good job my motor is brand new and want the best for it  thanks all
|
|
~AMP~
|
 |
|
Sponsored Links
|
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2012 at 10:52pm |
|
My WC was like that after I got all the crud cleaned off. It has a coating of gas tank liner in it now and works fine.
|
|
|
|
BrettPhillips
Orange Level
Joined: 11 Sep 2009
Location: Strasburg, VA
Points: 808
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 6:57am |
|
I have soft soldered a few of them successfully. If you're careful, you'll never know it was done when you're finished.
|
|
EdK
Silver Level
Joined: 12 Sep 2009
Location: Newcastle, CA
Points: 223
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 9:06am |
|
Not sure if it will work but you might try the spray on rubber stuff. I've seen it on TV and similar stuff at Home Depot, made by Rust-O-leum".
|
|
EdK
Silver Level
Joined: 12 Sep 2009
Location: Newcastle, CA
Points: 223
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 9:25am |
I replaced the oil can filter with a K&N cartridge filter. I enclosed it in a metal container, (soup can), for protection. Since this is only my casual use tractor I have yet to change or clean the filter after about 2 years. Not original but practical.
|
|
AC WD45
Orange Level
Joined: 28 Sep 2009
Location: Mid Michigan
Points: 2060
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 10:39am |
|
JB Weld
|
|
German Shepherd dad
1957 Allis Chalmers WD45
#WD234847
1951 Allis Chalmers WD
#WD88193
|
|
David(Stockbridge)MI
Orange Level
Joined: 15 Sep 2009
Location: Stockbridge MI
Points: 536
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 11:42am |
clamp style bowl NEW is about $19.00 on our site. www.djstractorparts.com
|
|
All "NEW" Web Site http://www.djstractorparts.com
2035,A,U,UC,WF unstyled,WF styled,WC High Crop (cane),RC,B,IB,C,CA,WD,WD45,G,D10,D12,D14,D15,D15 II,D17,D19,WC styled,WC unstyled H3 crawler
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 2:01pm |
|
All C's originally hand the 2 snap clips for the bowl which is different than the ring clamp bowl.
|
|
|
|
wfmurray
Orange Level
Joined: 13 Sep 2009
Location: Bostic NC
Points: 1225
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2012 at 2:39pm |
|
I used J B Weld on my B . It,s been on about 4 years.
|
|
