anyone know?
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=51483
Printed Date: 24 Aug 2025 at 6:50am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: anyone know?
Posted By: allismanamp
Subject: anyone know?
Date Posted: 02 Jun 2012 at 10:29pm
were i can get a new oil breather bowl for my allis chalmers c engine i was cleaning mine out today and held it up to the light only to see little pin holes where it has rotted out. should i just tuck a k&n oil air filter in the pipe under the hood off the breather? also do the original breathers really do good job my motor is brand new and want the best for it thanks all------------- ~AMP~ |
Replies:
Posted By: CTuckerNWIL
Date Posted: 02 Jun 2012 at 10:52pm
|
My WC was like that after I got all the crud cleaned off. It has a coating of gas tank liner in it now and works fine.
------------- http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
Posted By: BrettPhillips
Date Posted: 03 Jun 2012 at 6:57am
| I have soft soldered a few of them successfully. If you're careful, you'll never know it was done when you're finished. |
Posted By: EdK
Date Posted: 03 Jun 2012 at 9:06am
| Not sure if it will work but you might try the spray on rubber stuff. I've seen it on TV and similar stuff at Home Depot, made by Rust-O-leum". |
Posted By: EdK
Date Posted: 03 Jun 2012 at 9:25am
|
I replaced the oil can filter with a K&N cartridge filter. I enclosed it in a metal container, (soup can), for protection. Since this is only my casual use tractor I have yet to change or clean the filter after about 2 years. Not original but practical.    |
Posted By: AC WD45
Date Posted: 03 Jun 2012 at 10:39am
|
JB Weld ------------- German Shepherd dad 1957 Allis Chalmers WD45 #WD234847 1951 Allis Chalmers WD #WD88193 |
Posted By: David(Stockbridge)MI
Date Posted: 03 Jun 2012 at 11:42am
|
clamp style bowl NEW is about $19.00 on our site. http://www.djstractorparts.com" rel="nofollow - www.djstractorparts.com ------------- All "NEW" Web Site http://www.djstractorparts.com 2035,A,U,UC,WF unstyled,WF styled,WC High Crop (cane),RC,B,IB,C,CA,WD,WD45,G,D10,D12,D14,D15,D15 II,D17,D19,WC styled,WC unstyled H3 crawler |
Posted By: CTuckerNWIL
Date Posted: 03 Jun 2012 at 2:01pm
|
All C's originally hand the 2 snap clips for the bowl which is different than the ring clamp bowl.
------------- http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
Posted By: wfmurray
Date Posted: 03 Jun 2012 at 2:39pm
| I used J B Weld on my B . It,s been on about 4 years. |