7010 engine overhaul

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic


   My open station 7010 started dripping coolant out of the breather this summer and parked it after I noticed it.  I'm not sure when it started but it wasn't this way when I had the valve cover off late last winter and have only put less than 10 hours on it in the spring Have since dug into it and found a leak coming from between the number 6 sleeve and block.  It is tired and needs a freshening up anyway.  Wondering about what kit to use.  I did put an Absolute kit in my 190xt a few years ago and have been happy with it.  Seemed like a good kit and would probably go that way again.  I have also found a kit from Federal Power Products, wondering if anybody had any experience with this kit or not?  I am not interested in a Reliance kit.  Thanks

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
HagerAC Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 14 Sep 2010 Location: SE MN Points: 1197	Post Options Post Reply Quote HagerAC Report Post Thanks(0) Quote Reply Topic: 7010 engine overhaul Posted: 6 hours 10 minutes ago at 10:52am
	My open station 7010 started dripping coolant out of the breather this summer and parked it after I noticed it. I'm not sure when it started but it wasn't this way when I had the valve cover off late last winter and have only put less than 10 hours on it in the spring Have since dug into it and found a leak coming from between the number 6 sleeve and block. It is tired and needs a freshening up anyway. Wondering about what kit to use. I did put an Absolute kit in my 190xt a few years ago and have been happy with it. Seemed like a good kit and would probably go that way again. I have also found a kit from Federal Power Products, wondering if anybody had any experience with this kit or not? I am not interested in a Reliance kit. Thanks
	30+ A-Cs ranging from a 1928 20-35, to a 1984 8070FWA, Gleaner R52

Sponsored Links

tbran Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 14 Sep 2009 Location: Paris Tn Points: 3542	Post Options Post Reply Quote tbran Report Post Thanks(0) Quote Reply Posted: 1 hour 11 minutes ago at 3:51pm
	Sounds like you need block work more than an engine kit. I would check sleeves for roundness and re ring if ok - you will have to do a close inspection to determine what is needed - you are going to have to spend the money sleeving the block bottom bores quite possibly and by all means re-bearing all.
	When told "it's not the money,it's the principle", remember, it's always the money..

Leon B MO Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Sep 2009 Location: Old Monroe, Mo Points: 2206	Post Options Post Reply Quote Leon B MO Report Post Thanks(0) Quote Reply Posted: 1 hour 2 minutes ago at 4:00pm
	We rebuilt a 301 in our 200 January 2024. Used a Reliance kit from Agkits. Bought the gasket set from Agco. We were satisfied with the Reliance kit. Tractor starts and runs perfect. Gonna split an XT tomorrow for a rebuild. Plan to do it the same way. Sorry I couldn't be more helpful. Leon B Mo
	Uncle always said "Fill the back of the shovel and the front will take care of itself".