This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


AC 200 Shift plate assembly
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
MYAC200 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 19 May 2017
Location: Oklahoma
Points: 5 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MYAC200 Quote  Post ReplyReply Direct Link To This Post Topic: AC 200 Shift plate assembly
    Posted: 19 May 2017 at 7:19am
Good morning,
 
I have a problem getting the shift plate back on after changing the forks to fix the problem of slipping out of 3rd gear. My issue is that when the plate is back on, unable to shift into gears. Any ideas what the issue is? I believe the forks are in the proper position when it's bolted back on, but the shifter will not go into gear?
 
 
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 22332 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2017 at 7:25am
Shift cover AND THE TRANSMISSION must be in second gear. Be sure to install special dowel bolts in left front and right rear corners when sitting in the seat.
Back to Top
MYAC200 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 19 May 2017
Location: Oklahoma
Points: 5 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MYAC200 Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2017 at 7:45am
Dr Allis,
 
What not havaing the dowell bolts cause the shifter not to be able to shift?
 
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 22332 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2017 at 7:46am
I doubt it.
Back to Top
MYAC200 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 19 May 2017
Location: Oklahoma
Points: 5 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MYAC200 Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2017 at 8:25am
Using the 2nd gear position, we can get the shift plate on, in place and bolted with what looks like the correct fork position, but then the tractor still won't shift? Any other known issues that we could try?
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 22332 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2017 at 9:09am
If the cover shifts into ALL positions while clamped in a vise, you aren't getting the forks aligned with the shifting collars when you set it on the tractor. Rotate the trans gears so that if the 3rd/4th collar gets bumped it cannot move either way. Make sure reverse idler is rearward. Don't use any kind of line-up dowel. Just set it on and it will find it'd way into place.
Back to Top
MYAC200 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 19 May 2017
Location: Oklahoma
Points: 5 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MYAC200 Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2017 at 11:47am
ill try that. thanks
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.


Help Support the
Unofficial Allis Forum