| Author |
 Topic Search  Topic Options
|
51ACWD 
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: U Engine #
Posted: 21 Jun 2016 at 8:53pm |
|
Does anybody know what a U engine # of UM or UMA7601G denotes it as?just wanting to know the year maybe, and to see what fuel it took. It's in a 1936 U serial #12343
|
 |
|
Sponsored Links
|
|
|
everett048
Orange Level
Joined: 12 Sep 2009
Location: uk
Points: 619
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 1:31am |
|
G for gas K for kerosene(distillit) hope that helps.
Edited by everett048 - 22 Jun 2016 at 1:32am
|
|
51ACWD
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 7:11am |
|
They used letters K,G,H, and B on the U engines. K meant distillate 3,000 feet or below altitude. G was distillate between 3,000 and 6,000 feet and gasoline above that. All the letters were dual fuel, but they had different engines to run the most efficient at different altitudes
|
|
everett048
Orange Level
Joined: 12 Sep 2009
Location: uk
Points: 619
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 11:39am |
|
Sorry but i think you have that wrong G & K are fuel types,Engines also had a A after the G OR K to denote if it was high altitude pistons or not.Compression was designated by either 3 or 4 types of pistons 1 of them being flat top the others being dished to different measurements for the compression ratio.Where as the A & K motors the wrist pin was moved up or down the piston depending on fuel type,(different piston types)
|
|
51ACWD
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 12:07pm |
|
Even though my engine has the duel fuel tank, and dual fuel manifold?
|
|
51ACWD
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 12:10pm |
|
What I am reading on the engine is that the G code had a 4.7:1 compression ratio. Gasoline was to be used at 3000ft or below and distillate between 3000-6000 feet altitude
|
|
51ACWD
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 1:31pm |
|
Do you have any references I can read up?im not finding much out about the U's and just want to do some reading
|
|
everett048
Orange Level
Joined: 12 Sep 2009
Location: uk
Points: 619
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 3:54pm |
|
if it has the dual fuel tanks from new, it May have run on distillate with the exhaust in the middle and the K on the heat exchanger on the top side it may also have had the low comp pistons as well hence the engine n,o ending with a K. The pistons may have been replaced at some point with gas pistons.According to my DEALERS parts book piston part no 211658 with a 5/32 cupped top has a comp ratio of as you say 4.7-1 but how do you know what pistons are fitted?it could have part no 211657 cupped to 3/4 deep for kerosene.And i quote from the dealers parts book the letters UMA in a typical engine serial no such as UMA-25197K indicate that model of the engine while the letter K following the serial no indicates the the engine is equipped with pistons and other equipment necessary to use Kerosene as a fuel,If the letter G follows the serial no the engine is equipped to burn gas un quote.
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 4:10pm |
|
I would think a compression check could tell you what fuel you can burn in your engine .
Edited by CTuckerNWIL - 22 Jun 2016 at 4:23pm
|
|
|
|
51ACWD
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 4:11pm |
|
Weird. I know my manifold has BOTH spots on to change where my exhaust is ran at. Just a circular plate to cover which one is not being used. I am just simply asking. The engine has a FAINT A at the end of "UM" then under it has 7601G.
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8681
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 7:05pm |
|
my UC has kerosene pistons and runs fine on gasoline with the plate flipped.actually (it's been a while) I think it outlets the exhaust at a different spot for gas and kereo
Edited by SteveM C/IL - 22 Jun 2016 at 7:07pm
|
|
51ACWD
Silver Level
Joined: 24 Dec 2015
Location: United States
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jun 2016 at 8:50pm |
|
Mine has a plate on the side exhaust outlet and the exhaust dumps out the front under the hood. Has a spot for the dual fuel tank in the hood but is a G code engine. Why would it have the spot for a starting tank but have the g code for gasoline? And the manifold is a dual fuel manifold
|
|
everett048
Orange Level
Joined: 12 Sep 2009
Location: uk
Points: 619
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Jun 2016 at 1:37am |
|
Almost all the manifolds were dual fuel except for the very early ones the first dual fuel one,s had a removable plate that you could either have in the front to run on low grade fuel or in the centre with a front exhaust to run on gas,they then changed to the next type witch you the exhaust was in the center and you just turned the plate to either G at the top or K at the top depending on fuel.As for the G on your engine no reread my previous post it is explained in that,Also your hood having a starting tank fitted was it original to the tractor? or has it come from another U as yours was damaged ? there is probably no way of knowing for sure.
|
|
