| Author |
 Topic Search  Topic Options
|
Daniel 
Bronze Level
Joined: 09 May 2012
Location: Oklahoma
Points: 16
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Disc identification
Posted: 12 Oct 2012 at 4:50pm |
|
|
 |
|
Sponsored Links
|
|
|
EricPA
Orange Level
Joined: 13 Sep 2009
Location: Watsontown,PA.
Points: 2578
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Oct 2012 at 4:55pm |
|
international harvester
|
|
Life is tough,but it's tougher when you're stupid. - John Wayne
|
|
Teddy (punchie)
Orange Level
Joined: 14 Jan 2010
Location: Beaver PA
Points: 258
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Oct 2012 at 7:57pm |
|
Yes IH old I would say 50 years any way maybe more. I have two; one in the scrap and one setting. I was a very young the last time we used one. Looks to be just the front, most had a back section to.
|
|
Ac D-19, a Number of WD's, One WD45, Two 444 balers, Ac plows and etc.
|
|
Scott(SC)
Orange Level
Joined: 11 Sep 2009
Location: Starr, SC
Points: 397
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Oct 2012 at 8:33pm |
|
I have a 20 disk and a 16 disk. I was told they are 19B International. Kaleb and I used them today and they sure do a good job.
|
|
Daniel
Bronze Level
Joined: 09 May 2012
Location: Oklahoma
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Oct 2012 at 11:15pm |
|
Thank you! You guys are so great!
I'm wanting to use this disc, is there anything other than greasing up the bearings I need to do?
|
|
Teddy (punchie)
Orange Level
Joined: 14 Jan 2010
Location: Beaver PA
Points: 258
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2012 at 3:04am |
|
That should be about it, greasing the bearings. If they have gotten to the point where they are steel on steel, or worn lose. I make packing from old twine and grease. Rapping it the right direction is needed, Like putting on tiflon (sp) tape, one way it works the other it just comes of. Don't over do it the with the twine shaft will not turn.
|
|
Ac D-19, a Number of WD's, One WD45, Two 444 balers, Ac plows and etc.
|
|
David Maddux
Orange Level
Joined: 13 Sep 2009
Points: 2535
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2012 at 5:07am |
|
I bet it is over 50 years old. I am over 50 and I don't look that bad.
|
|
Daniel
Bronze Level
Joined: 09 May 2012
Location: Oklahoma
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2012 at 12:25pm |
 Teddy (punchie) wrote:
That should be about it, greasing the bearings. If they have gotten to the point where they are steel on steel, or worn lose. I make packing from old twine and grease. Rapping it the right direction is needed, Like putting on tiflon (sp) tape, one way it works the other it just comes of. Don't over do it the with the twine shaft will not turn.
|
Teddy, I will be giving it a look over Sunday, thank you for your advice!
Daniel
|
|
Jim Hancock
Orange Level
Joined: 11 Sep 2009
Location: EL Reno, Ok.
Points: 1112
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2012 at 5:36pm |
Hi Daniel. I've got it's cousin here west of Mustang that has the back gang. Same hitch setup, too! Where are you in Oklahoma?
|
|
Daniel
Bronze Level
Joined: 09 May 2012
Location: Oklahoma
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2012 at 9:54pm |
|
Hello Jim! That is great, I live south of Tulsa about 50 miles! Glad to see another okie here!
What is a "back gang" Jim?
|
|
EricPA
Orange Level
Joined: 13 Sep 2009
Location: Watsontown,PA.
Points: 2578
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2012 at 10:02pm |
|
it is another row of discs similar to what you have that attach to the rear that are angled opposite to what you have to make a more level seedbed
|
|
Life is tough,but it's tougher when you're stupid. - John Wayne
|
|
