This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Gleaner E and All cylinder
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Carl(NWWI) View Drop Down
Orange Level
Orange Level


Joined: 13 Sep 2009
Location: NW WI
Points: 954 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Carl(NWWI) Quote  Post ReplyReply Direct Link To This Post Topic: Gleaner E and All cylinder
    Posted: 21 Nov 2016 at 10:03am
Been doing some research trying to find new cylinder bars for the E and A2 but I'm not coming up with anything short of calling an AGCO dealer. Are there any aftermarket suppliers that still offer them? Does AGCO still offer them? Looking to do corn, beans, oats, wheat and rye with them.

Thanks. Carl
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21490 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 10:07am
E-E3-K-K2 are all the same. The A-A2 is an orphan.
Back to Top
Skyhighballoon(MO) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Pilot Grove, MO
Points: 3115 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Skyhighballoon(MO) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 10:08am
Google Trimpe Hard Surface Bars and St. Johns Welding.   Mike
1981 Gleaner F2 Corn Plus w 13' flex
1968 Gleaner EIII w 10' & 330
1969 180 gas
1965 D17 S-IV gas
1963 D17 S-III gas
1956 WD45 gas NF PS
1956 All-Crop 66 Big Bin
303 wire baler, 716H, 712H mowers
Back to Top
Tbone95 View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 31 Aug 2012
Location: Michigan
Points: 12016 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tbone95 Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 10:48am
I bet St. Johns would make something for you. Even if you had to send in an old one (which I doubt you would).
Back to Top
Carl(NWWI) View Drop Down
Orange Level
Orange Level


Joined: 13 Sep 2009
Location: NW WI
Points: 954 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Carl(NWWI) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 12:20pm
So the A uses different ones then the E and K?
Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8522 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 12:51pm
The A/A2 cyl is wider than E-K's
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21490 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 12:54pm
The A-A2 had three wide straw walkers. The C-C2 had four wide straw walkers. These two machines were based off of each other so to speak. The E-E3-K-K2 also had three walkers, but there were an inch or two narrower.
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 21 Nov 2016 at 9:29pm
I have a set for A-A2 that I cut ever other tooth out then built back up that I would sell cheap. Went to F2.    MACK
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum