72 All Crop Cylinder Bars

Author

Message

Topic Search

Topic Options

tbran

Orange Level

Joined: 14 Sep 2009
Location: Paris Tn
Points: 3526

Post Options

Post Reply

Quote tbran

Report Post

Thanks(0)

Quote

Topic: 72 All Crop Cylinder Bars
Posted: 16 Jun 2025 at 11:13am

Any source for them ? Thresher plate and rubber ?

When told "it's not the money,it's the principle", remember, it's always the money..

Sponsored Links

560Dennis

Bronze Level

Joined: 30 Apr 2011
Location: NE OHIO
Points: 125

Post Options

Post Reply

Quote 560Dennis

Report Post

Thanks(0)

Quote

Posted: 17 Jun 2025 at 6:31am

Tom Yaz is a source , the all crop fourm may be still up and operational .I have us not ed it for a long time.

So best I can help with ?

Whats wrong with yours? Bent , rubber gone worn off out ? Id investagate a high impact plasctic. That being said never tested it ,may bust seed .

DanielW

Silver Level

Joined: 19 Sep 2022
Location: Ontario
Points: 220

Post Options

Post Reply

Quote DanielW

Report Post

Thanks(0)

Quote

Posted: 17 Jun 2025 at 1:17pm

Several years ago for my 90 I had some bars made: Steel was cut and formed at work, and I then sent them out to a place we use at work for rubber lagging that cast 90-durometer urethane directly onto them to mimic the original rubber/steel bars. The price wasn't actually that bad, but I'm not really sure why I bothered with the urethane. I'm not doing any fancy/sensitive seed crops. For any of the cereal grains I'm doing, I could have just used plain steel bars (thicker than the original) and they would have worked just as good.

Any decent fab shop with a plasma table and brake press should be able to make the bars. And if you want to go whole-hog and do the urethane, there are lots of places that can do it. The place we use is 'Prothane' in Toronto, but any other urethane casting shop could do the same.

Edited by DanielW - 17 Jun 2025 at 1:22pm

N186364

Bronze Level

Joined: 05 Jan 2020
Location: Ontario, Canada
Points: 30

Post Options

Post Reply

Quote N186364

Report Post

Thanks(0)

Quote

Posted: 4 hours 50 minutes ago at 4:08pm

560Dennis had hit right, Tom Yaznowski at allcropharvester.com sells new reman cylinder bars for all crop combines. I purchased a set of 8 and they are exact replicas of the originals. They have a 1/2in rubber vulcanized facing, are the correct dimensions, and pre-drilled for the mounting bolts. These bars will fit any of the three All Crop pull type combines, 60,66 and 72. Contact Tom for price and such. On the concave bars, in July 2020 I was able to get a set ( 2 ) from AGCO under part numbers 70513658 ( bar ) and 70535533 ( rubber insert ) also 2 required. If AGCO no longer carries these, ask Tom. I've been told you can replace the shelling plate rubber with rubber from bale thrower belt on small square balers. In order to attach the rubber to the shelling plate you will need 27 split rivets just like the original used. Good luck.

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
tbran Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 14 Sep 2009 Location: Paris Tn Points: 3526	Post Options Post Reply Quote tbran Report Post Thanks(0) Quote Reply Topic: 72 All Crop Cylinder Bars Posted: 16 Jun 2025 at 11:13am
	Any source for them ? Thresher plate and rubber ?
	When told "it's not the money,it's the principle", remember, it's always the money..

Sponsored Links

560Dennis Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 30 Apr 2011 Location: NE OHIO Points: 125	Post Options Post Reply Quote 560Dennis Report Post Thanks(0) Quote Reply Posted: 17 Jun 2025 at 6:31am
	Tom Yaz is a source , the all crop fourm may be still up and operational .I have us not ed it for a long time. So best I can help with ? Whats wrong with yours? Bent , rubber gone worn off out ? Id investagate a high impact plasctic. That being said never tested it ,may bust seed .

DanielW Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 19 Sep 2022 Location: Ontario Points: 220	Post Options Post Reply Quote DanielW Report Post Thanks(0) Quote Reply Posted: 17 Jun 2025 at 1:17pm
	Several years ago for my 90 I had some bars made: Steel was cut and formed at work, and I then sent them out to a place we use at work for rubber lagging that cast 90-durometer urethane directly onto them to mimic the original rubber/steel bars. The price wasn't actually that bad, but I'm not really sure why I bothered with the urethane. I'm not doing any fancy/sensitive seed crops. For any of the cereal grains I'm doing, I could have just used plain steel bars (thicker than the original) and they would have worked just as good. Any decent fab shop with a plasma table and brake press should be able to make the bars. And if you want to go whole-hog and do the urethane, there are lots of places that can do it. The place we use is 'Prothane' in Toronto, but any other urethane casting shop could do the same. Edited by DanielW - 17 Jun 2025 at 1:22pm

N186364 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 05 Jan 2020 Location: Ontario, Canada Points: 30	Post Options Post Reply Quote N186364 Report Post Thanks(0) Quote Reply Posted: 4 hours 50 minutes ago at 4:08pm
	560Dennis had hit right, Tom Yaznowski at allcropharvester.com sells new reman cylinder bars for all crop combines. I purchased a set of 8 and they are exact replicas of the originals. They have a 1/2in rubber vulcanized facing, are the correct dimensions, and pre-drilled for the mounting bolts. These bars will fit any of the three All Crop pull type combines, 60,66 and 72. Contact Tom for price and such. On the concave bars, in July 2020 I was able to get a set ( 2 ) from AGCO under part numbers 70513658 ( bar ) and 70535533 ( rubber insert ) also 2 required. If AGCO no longer carries these, ask Tom. I've been told you can replace the shelling plate rubber with rubber from bale thrower belt on small square balers. In order to attach the rubber to the shelling plate you will need 27 split rivets just like the original used. Good luck.