This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Enameled sink |
Post Reply |
Author | |
Hubert (Ga)engine7
Orange Level Joined: 12 Sep 2009 Location: Jackson Cnty,GA Points: 6136 |
Post Options
Thanks(0)
Posted: 22 Dec 2019 at 9:29pm |
Had a lady at church tonight ask me if the enameling on a cast iron kitchen sink could be redone. She had a sink from the 1950's that she would like to save. Any tips or thoughts on the idea? I would think it would be less expensive to buy a new high end sink.
|
|
Just an old country boy saved by the grace of God.
|
|
Sponsored Links | |
CaseyCreek
Silver Level Joined: 03 Apr 2011 Location: L.A. Points: 332 |
Post Options
Thanks(0)
|
I haven't tried this stuff yet, but I looked it up a while back when I was thinking about refinishing a porcelain bathtub. The price isn't too bad; about $25. |
|
D17 Series III,D17 Series IV, 185
|
|
Dakota Dave
Orange Level Joined: 12 Sep 2009 Location: ND Points: 3894 |
Post Options
Thanks(0)
|
Nieghbor repaired a claw foot cast iron tub. Used a porcelain repair kit it was a two part epoxy turned out real nice its held up a couple years so far outside as yard art.
|
|
Clay
Orange Level Joined: 11 Sep 2009 Location: Udall, Kansas Points: 8834 |
Post Options
Thanks(0)
|
Mask of the area to be repaired and lightly blast with black beauty (coal sl*g). Degrease with acetone. Warm the surface. Do not get the surface above 100 deg. F. or the amines will boil out of the coating. Some coating manufacturers want the temperature range to be no higher than 90 or lower than 50.
***** Wear chemical resistant (latex) gloves. Follow the directions of the coating manufacturer. If you have questions, call their technical department. ***** As with painting...it is better to have a higher temperature, when the coating is applied, and let it cool down. If you start out with a cool temperature and raise the temperature, there is a good possibility of out gassing (bubbles and pin holes).
Edited by Clay - 22 Dec 2019 at 11:53pm |
|
thendrix
Orange Level Joined: 04 Feb 2013 Location: Fairmount GA Points: 4740 |
Post Options
Thanks(0)
|
My folks have a cast iron sink that they just had redone to go in their new house. Their builder got it sand blasted and powder coated and it looks great.
|
|
"Farming is a business that makes a Las Vegas craps table look like a regular paycheck" Ronald Reagan
|
|
Pat the Plumber CIL
Orange Level Joined: 11 Sep 2009 Location: Springfield,Il Points: 4684 |
Post Options
Thanks(0)
|
Google tub refinishing in your area and see what comes up . If it can be sent off and done professionally it will last a lot longer . Never seen anything done on site last more than a few years before it starts to peel . Most will only guarantee for a year or two . Factory setting where it can be properly prepped and finished under proper heat , temp , pressure is the way to go . Around here they have to be sent off to Chicago or St. Louis to be properly refinished .
|
|
You only need to know 3 things to be a plumber;Crap rolls down hill,Hot is on the left and Don't bite your fingernails
1964 D-17 SIV 3 Pt.WF,1964 D-15 Ser II 3pt.WF ,1960 D-17 SI NF,1956 WD 45 WF. |
|
chaskaduo
Orange Level Joined: 26 Nov 2016 Location: Twin Cities Points: 5203 |
Post Options
Thanks(0)
|
As I mentioned in the enamel cookware post earlier. Remember a kitchen sink gets a lot of abuse from dishes and pots and pans. So I would make sure that it is a fired type of refinish (or glaze) and not an epoxy type which may be OK for tub or shower.
Edited by chaskaduo - 23 Dec 2019 at 9:27am |
|
1938 B, 79 Dynamark 11/36 6spd, 95 Weed-Eater 16hp, 2010 Bolens 14hp
|
|
Hubert (Ga)engine7
Orange Level Joined: 12 Sep 2009 Location: Jackson Cnty,GA Points: 6136 |
Post Options
Thanks(0)
|
Many thanks for all of the replies. I will relay this information to her. The smartest people around are on this Forum.
|
|
Just an old country boy saved by the grace of God.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |