This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


7040 PD troubles
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Lynn TN View Drop Down
Bronze Level
Bronze Level


Joined: 29 Nov 2009
Location: Maryville, TN
Points: 130 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lynn TN Quote  Post ReplyReply Direct Link To This Post Topic: 7040 PD troubles
    Posted: 12 Jul 2017 at 7:49am
Been bushhogging with our 7040 when you load the tractor either by being in thick weeds or going up hill the PTO will slow way down then the ground speed will nearly stop as well. When you stop and let it clean out it will go again fine. Filters are good as well as both sections full of oil. Didn't know if it's a pump problem or what. Tractor has 7000 hours but hate to junk it still looks and runs good.
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 22365 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jul 2017 at 7:57am
Sounds like torque limiter on the flywheel.
Back to Top
Lynn TN View Drop Down
Bronze Level
Bronze Level


Joined: 29 Nov 2009
Location: Maryville, TN
Points: 130 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lynn TN Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jul 2017 at 8:16am
Meant to also say transmission pressure above 1800 light stays on till pretty much wide open as well and back on when it slips.
Back to Top
Orange Blood View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Nov 2010
Location: ColoradoSprings
Points: 4053 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Orange Blood Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jul 2017 at 8:58am
No need to junk it, if it is the Torque limiter, you just need to split the tractor and replace it, just like the dry engine clutch of old.  You will likely need to take a hard look at your flywheel, and the pressure plate, if it has been slipping like that for long, likely it is shot from heat stress.
Still in use:
HD7 WC C CA WD 2-WD45 WD45LP WD45D D14 3-D17 D17LP 2-D19D D19LP 190XTD 190XTLP 720 D21 220 7020 7030 7040 7045 3-7060
Projects: 3-U UC 2-G 2-B 2-C CA 7-WC RC WDLP WF D14 D21 210 7045 N7
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 13 Jul 2017 at 9:52pm
Have flywheel resurfaced, new disc, and new pressure plate. Never mix old with new parts in a torque limiter.     MACK
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.080 seconds.


Help Support the
Unofficial Allis Forum