This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


8 foot disk additional weight ?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Pointer Hollow Farm View Drop Down
Bronze Level
Bronze Level


Joined: 28 Oct 2025
Location: PA
Points: 71 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pointer Hollow Farm Quote  Post ReplyReply Direct Link To This Post Topic: 8 foot disk additional weight ?
    Posted: 20 hours 30 minutes ago at 6:26pm
On this disk someone has welded two bolts on the frame (a set on each half), I assume to add weight to the disk.  I was thinking about adding some weight and I have some wheel weights.  The weights I have weigh about 140#'s each.  Would it be too much to add the extra 140#'s to each side or would that be too much for the bearings, etc.

I was debatiing on doing that or adding one 140# weight in the center of the disk.

Thoughts?
Back to Top
Sponsored Links


Back to Top
AC720Man View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5322 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC720Man Quote  Post ReplyReply Direct Link To This Post Posted: 17 hours 55 minutes ago at 9:01pm
Common addition of weight locally is a rail road tie cut to length. Haven’t seen them cause any issues.
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
Back to Top
IBWD MIke View Drop Down
Orange Level
Orange Level
Avatar

Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4200 		Post Options Post Options   Thanks (0) Thanks(0)   Quote IBWD MIke Quote  Post ReplyReply Direct Link To This Post Posted: 8 hours 29 minutes ago at 6:27am
Probably the bigger problem you'll run into is keeping the front-end on the ground.  Too much weight and picking the disc up could be a problem too.
Back to Top
Pointer Hollow Farm View Drop Down
Bronze Level
Bronze Level


Joined: 28 Oct 2025
Location: PA
Points: 71 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pointer Hollow Farm Quote  Post ReplyReply Direct Link To This Post Posted: 7 hours 41 minutes ago at 7:15am
I just added 300 pounds in weight to the front.
Back to Top
Gary Burnett View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Virginia
Points: 3127 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary Burnett Quote  Post ReplyReply Direct Link To This Post Posted: 7 hours 22 minutes ago at 7:34am
If its not cutting enough a pull type (drawbar hitch) disc is the way to go,they will cut better and you can add all the wieght you can pull no problem.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.039 seconds.


Help Support the
Unofficial Allis Forum