This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


59L Belt twists
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Hubnut View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Jul 2014
Location: Gainesville, FL
Points: 1817 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hubnut Quote  Post ReplyReply Direct Link To This Post Topic: 59L Belt twists
    Posted: 02 Aug 2015 at 6:41pm
Trying to figure out the belt twists for the 59L.  The biggest twist I have is from the PTO pulley to the lower pulley.  Across these pulleys there is a full one twist.  Is this correct?
Back to Top
Sponsored Links


Back to Top
norm[ind] View Drop Down
Orange Level
Orange Level


Joined: 29 Oct 2010
Location: bourbon,ind
Points: 2992 		Post Options Post Options   Thanks (0) Thanks(0)   Quote norm[ind] Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2015 at 6:55pm
  should havvve a decal on the mower --was on the ones we sold -or guard
Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2015 at 7:04pm

A half twist from drive pulley to the idler. A full twist would put you right back where you started.

https://www.google.com/search?q=Woods+L59+belt+routing&newwindow=1&tbm=isch&tbo=u&source=univ&sa=X&ved=0CDcQsARqFQoTCMOY9_zNi8cCFch7kgodREADXQ&biw=1024&bih=667#imgrc=_


Edited by CTuckerNWIL - 02 Aug 2015 at 7:06pm
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
Hubnut View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Jul 2014
Location: Gainesville, FL
Points: 1817 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hubnut Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2015 at 8:22pm
This is the way I had it and it worked.



However, this really results in a big twist to the center sheave.



but, according to the manual, this is correct:


 which is correct?
Back to Top
Auntwayne View Drop Down
Orange Level
Orange Level


Joined: 23 Apr 2011
Location: Edwardsville Il
Points: 1589 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Auntwayne Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2015 at 9:48pm
   You need to undo the belt as it is already twisted to much . Start over and you will have the correct 1/2 turn .
Back to Top
pumpkinman View Drop Down
Orange Level
Orange Level
Avatar

Joined: 20 Jul 2011
Location: S.E. Michigan
Points: 252 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pumpkinman Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2015 at 11:49pm
    The belt makes a  3/4 twist [to the left] to the top pulley then a 1/2 twist[to the right] over the drive pulley then a 1/4 twist [to the left] under the lower pulley                          
adjust The top pulley about one inch above being in line with the top grove of the center sheave and the rear or lower idler about one inch below being in line with the bottom groove of the center sheave on the mower.
  Make major belt adjustments by moving mower fore and aft
   
 RUN THE BELT TIGHT                                                                                                   --------------------                 KENT                                                                                                              
Back to Top
Hubnut View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Jul 2014
Location: Gainesville, FL
Points: 1817 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hubnut Quote  Post ReplyReply Direct Link To This Post Posted: 03 Aug 2015 at 10:09am
Okay.  I pulled the belt and tried again.  This is what I have now. All observed from behind tractor: 3/4 twist on left (to center sheave), 1/4 twist on right (to center sheave), 1/2 twist from drive pulley to left idler pulley.  Please tell me this is correct.  I had the same problem with my dryer belt.Wink
Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 03 Aug 2015 at 1:50pm
That sounds about right to me. No twist from right idler to drive pulley.
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
Hubnut View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Jul 2014
Location: Gainesville, FL
Points: 1817 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hubnut Quote  Post ReplyReply Direct Link To This Post Posted: 03 Aug 2015 at 8:12pm
Originally posted by CTuckerNWIL CTuckerNWIL wrote:

That sounds about right to me. No twist from right idler to drive pulley.


Correct.  No twist.  Thank you sir.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum