| Author |
 Topic Search  Topic Options
|
jaybmiller 
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24664
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: D-14 clutch installation
Posted: 15 Mar 2012 at 7:46am |
Ok,silly me didn't take any pictures before I removed the clutch to replace the ring gear.
Now I see that the clutch disc has different heights of the center splined 'hub'. None of the drawings or pictures I have show if it's important which side goes to the flywheel.My luck says I'll do it wrong..so can anyone help?
thanks
Jay
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
 |
|
Sponsored Links
|
|
|
JeffMOnt
Silver Level
Joined: 11 Sep 2009
Location: Ottawa, Ont
Points: 129
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 8:18am |
Jay, this is what I found in my manual. "longer hub and springs of the lined disc facing toward rear."
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24664
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 8:42am |
THANKS !!
hmm..longer hub I understand...'and springs of the lined disc' ???
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
JeffMOnt
Silver Level
Joined: 11 Sep 2009
Location: Ottawa, Ont
Points: 129
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 9:47am |
|
Must have been different versions of the clutch disc between factory and aftermarket. Probably had revisions along the way.
|
|
Rick
Orange Level
Joined: 11 Sep 2009
Location: Jonesburg,Mo.
Points: 3695
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 12:34pm |
|
The longer part of the hub and the spring cage (if it's a spring loaded disc) will go to the pressure plate side or towards the rear of the tractor. Rick
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24664
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 1:05pm |
OK...long hub to the back.......yes, it's an aftermarket unit (1/3rd the cost from A-C dealer !).
Man I gotta start taking pictures........
thanks
Jay
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
Tracy Martin TN
Orange Level Access
Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10769
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 2:25pm |
|
Jay, I hope it is correct. Most are not . Measure your finger height when installed on flywheel. If not correct thickness clutch is used with pressure plate machined correct ,your clutch will fail. HTH Tracy Martin
|
|
No greater gift than healthy grandkids!
|
|
79fordblake
Orange Level
Joined: 01 Jul 2010
Location: West Kentucky
Points: 829
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Mar 2012 at 4:51pm |
|
Maybe I'm miss understanding your comment but I just did a clutch job on a D17....the book gives you the spec for the finger height and you adjust them accordingly.
|
|
