| Author |
 Topic Search  Topic Options
|
Rugerben 
Bronze Level
Joined: 09 Sep 2016
Location: Alden, NY
Points: 18
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Allis B plow help
Posted: 29 Sep 2016 at 8:04pm |
|
|
 |
|
Sponsored Links
|
|
|
DiyDave
Orange Level Access
Joined: 11 Sep 2009
Location: Gambrills, MD
Points: 53544
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Sep 2016 at 8:48pm |
|
Not sure what the terminology is, but you reverse the curved drawbar, it mounts to the 2 bolt holes, in each final drive, then there is a part up front, that has a lever with notches, on it, to control the depth setting, IIRR...
|
|
Gerald J.
Orange Level
Joined: 12 Sep 2009
Location: Hamilton Co, IA
Points: 5636
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Sep 2016 at 9:03pm |
|
|
|
Rugerben
Bronze Level
Joined: 09 Sep 2016
Location: Alden, NY
Points: 18
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 Sep 2016 at 8:33am |
Sorry about the pic size. I'll address that next time I post :)
So do I need a drawbar to connect the plow or are you saying that I simply bolt those two bars that rotate on the cross bar directly to the final drives? they each have one hole in the end that is not threaded.
Also I don't have a hand lift, just hte hydralics. On the front under the brakes there are two bars that turn with the shaft. One has a bar that goes back to the hyralic ram (currently disconnected). I did not think I needed it connected for the plow. Here are pics:
|
|
Rugerben
Bronze Level
Joined: 09 Sep 2016
Location: Alden, NY
Points: 18
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Oct 2016 at 7:48pm |
|
Anyone know where i can get some drawbar anchors to connect the plow to my final drive?
|
|
Larry in NC
Orange Level
Joined: 09 Feb 2016
Location: NC
Points: 1050
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Oct 2016 at 8:02pm |
You can usually find them on eBay if a forum member does not respond. One set is listed now.
http://www.ebay.com/sch/i.html?_from=R40&_trksid=p3984.m570.l1313.TR1.TRC0.A0.H0.Xallis+chalmers+drawbar.TRS0&_nkw=allis+chalmers+drawbar&_sacat=0
|
|
Rugerben
Bronze Level
Joined: 09 Sep 2016
Location: Alden, NY
Points: 18
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Oct 2016 at 2:37pm |
Thank you. As far as I can tell they should look like the first picture below right? I found the ones in the second picture on ebay. Do you think they would work even though they do not have a sleeve for the plow bar to go into? Thanks again for all your help.
|
|
Chalmersbob
Orange Level
Joined: 11 Sep 2009
Location: Pennsylvania
Points: 2122
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Oct 2016 at 9:31pm |
I have a pair if your interested. Private mail me
|
|
4 B's, 1 C's,3 CA's, 2 G's WD, D14, D15, B-1, B10, B12, 712S,
|
|
Bill Long
Orange Level
Joined: 12 Sep 2009
Location: Bel Air, MD
Points: 4556
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2016 at 9:51am |
Usually what happens is that they stay on the tractor and when the plow is sold they forget to include them. I remember when we traded in equipment that we had to be certain we took the connector off the final drives for the plow. Looks like you have an excellent B. Thank you for taking such good care of my favorite. Good Luck! Bill Long
|
|
Bill Long
Orange Level
Joined: 12 Sep 2009
Location: Bel Air, MD
Points: 4556
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2016 at 9:52am |
|
|
|
Rugerben
Bronze Level
Joined: 09 Sep 2016
Location: Alden, NY
Points: 18
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2016 at 10:00am |
|
Thanks Bill! I am getting it together bit by bit...i had a line on a complete two way plow setup with all mounting hardware and lever for $100 on craigslist but it was sold before I could get there! I'll keep looking. I still have time before spring.
|
|
