| Author |
 Topic Search  Topic Options
|
coggonobrien 
Orange Level Access
Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1846
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: powermax rototiller pto shaft question
Posted: 11 May 2017 at 2:10pm |
|
should the pto for a 616/620/720 rototiller be able to pull in half? Mine is stuck hard (not the shield) and I'm running out of ideas to get it free.
|
 |
|
Sponsored Links
|
|
|
ac720nut
Orange Level
Joined: 09 Feb 2016
Location: Dexter Mi
Points: 1217
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2017 at 5:32am |
It may sound strange but I had one I couldn't get apart and soaked it good then I chained one end to my dually and other to my Silverado and pulled them apart , it worked for me. May not be everyones cup of tea.
|
|
coggonobrien
Orange Level Access
Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1846
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2017 at 5:37am |
|
I chained mine to the ton cylinder on my cherry picker and kept snapping the bolts holding the chain
|
|
ac720nut
Orange Level
Joined: 09 Feb 2016
Location: Dexter Mi
Points: 1217
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2017 at 12:59pm |
|
Wow! can't say I've ever heard of one that tight till now
. Be careful or you'll bend it
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5131
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2017 at 8:51pm |
|
I put my brush hog pto between to metal support posts in my garage. Strapped one end to one post and a come along to the other utilizing 5,000lb soft straps. Tightened it up. I had been greasing and using Kroil on it for 2 days. I let it set over night. The next day I took a map gas torch and heated the stuck area. Within 10 minutes one click at a time it came apart without damage.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
coggonobrien
Orange Level Access
Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1846
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 May 2017 at 6:20am |
|
How are you guys holding on with the straps? Through theknuckle of the u joint?
|
|
Bird76Mojo
Silver Level
Joined: 12 Mar 2015
Location: Illinois
Points: 221
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 May 2017 at 8:22pm |
|
Be sure to apply a good grease, with added anti-seize, liberally to the inside of the slip yoke after you get it apart.
GB :)
|
|
coggonobrien
Orange Level Access
Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1846
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 May 2017 at 7:19am |
|
well i got it apart. hard to tie 1 end to a railed tie fence post with a cable clevice and the other to the skid loader in the same fashion. Came with a pop but its wierd, the shaft is rust free and greased.
|
|
ac720nut
Orange Level
Joined: 09 Feb 2016
Location: Dexter Mi
Points: 1217
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 May 2017 at 8:28pm |
|
Is it bent a little ? doesn't take much
|
|
coggonobrien
Orange Level Access
Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1846
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 May 2017 at 8:47am |
|
I'm wondering if you are right on it being slightly bent. I will not slide together fully after pulling it apart
|
|
