This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Hand clutch adjustment CA (need help) |
Post Reply |
Author | |
Hubnut
Orange Level Joined: 30 Jul 2014 Location: Gainesville, FL Points: 1812 |
Post Options
Thanks(0)
Posted: 27 May 2016 at 6:10pm |
I got my CA back together and test drove it today. Everything is good except the hand clutch won't disengage. Just had Rick C rebuild it, so I know it's just an adjustment thing. Which way do I turn the clutch cog in the final drive to make the clutch disengage?
|
|
1940 B "Lucy"
1941 B w/ Woods L59 "Flavia" 1942 B w/ finish mower "Dick" 1941 C w/ 3-point "Maggie" 1947 C SFW w/ L306 "Trixie" 1972 314H |
|
Sponsored Links | |
PaulB
Orange Level Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4451 |
Post Options
Thanks(0)
|
When your looking down in the hole the throwout bearing need to get closer to the clutch pack. The specified setting it .050" as long as it isn't turning the bearing it will be fine the extra clearance is just to allow for wear.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
If you can't make it GO... make it SHINY |
|
GregLawlerMinn
Orange Level Joined: 11 Sep 2009 Location: Lawler, Mn Points: 1226 |
Post Options
Thanks(0)
|
Can't remember the direction of rotation; however, you can do this. Check the gap between the clutch and actuator; adjust the cog until you have 0.020-0.040" clearance. If you can't disengage then, the clutch may be froze to the pressure plate.
|
|
What this country needs is more unemployed politicians-and lawyers.
Currently have: 1 D14 and a D15S2. With new owners: 2Bs,9CAs,1WD,2 D12s,5D14s,3D15S2s, 2D17SIVs,D17D,1D19D;1 Unstyled WC |
|
Hubnut
Orange Level Joined: 30 Jul 2014 Location: Gainesville, FL Points: 1812 |
Post Options
Thanks(0)
|
Thanks guys. Where am I supposed to measure this gap you're talking about?
|
|
1940 B "Lucy"
1941 B w/ Woods L59 "Flavia" 1942 B w/ finish mower "Dick" 1941 C w/ 3-point "Maggie" 1947 C SFW w/ L306 "Trixie" 1972 314H |
|
Rick
Orange Level Joined: 11 Sep 2009 Location: Jonesburg,Mo. Points: 3642 |
Post Options
Thanks(0)
|
That measurement would be between the throw out bearing face and the pressure plate assembly, where it makes contact. Rick
|
|
Hubnut
Orange Level Joined: 30 Jul 2014 Location: Gainesville, FL Points: 1812 |
Post Options
Thanks(0)
|
I see it now. Thanks. The distance is pretty wide. I'll tighten it up tomorrow.
|
|
1940 B "Lucy"
1941 B w/ Woods L59 "Flavia" 1942 B w/ finish mower "Dick" 1941 C w/ 3-point "Maggie" 1947 C SFW w/ L306 "Trixie" 1972 314H |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |