This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D17 Generator |
Post Reply |
Author | |
bincitybandit
Silver Level Joined: 14 Aug 2011 Location: North Dakota Points: 125 |
Post Options
Thanks(0)
Posted: 27 Dec 2011 at 3:49pm |
I know my D17 is a positive ground system. When I got the tractor the battery was hooked up as negative ground. I changed it back to positive ground. It is not charging. I'm wondering if the generator is bad or if it was replaced at some point with a negative ground generator. The number on the generator is 1100305 8C12, I believe. The very first 0 could potentially be a 3, it is difficult to read.
|
|
ALLIS: B, WC, G, G, D10, D12, D14, D14(NF), D15, D17, D17(NF), D19, D21, D21
MINNEAPOLIS MOLINE: U, U, U(NF), GB JOHN DEERE: L FORD: 871 Select-O-Speed CASE: 600 Combine |
|
Sponsored Links | |
GregLawlerMinn
Orange Level Joined: 11 Sep 2009 Location: Lawler, Mn Points: 1226 |
Post Options
Thanks(0)
|
Did you re-polarize the VR when you switched the battery polarity (and before you started the engine)? How about the leads on the ammeter? If not, you may have to replace the VR and polarize it and switch the leads on the ammeter.
|
|
What this country needs is more unemployed politicians-and lawyers.
Currently have: 1 D14 and a D15S2. With new owners: 2Bs,9CAs,1WD,2 D12s,5D14s,3D15S2s, 2D17SIVs,D17D,1D19D;1 Unstyled WC |
|
Tony.Or
Orange Level Joined: 18 Mar 2010 Location: Oregon Points: 1498 |
Post Options
Thanks(0)
|
That is correct gen number for 12 volt D-17 no listing for + or - grd. Tony
|
|
Gerald J.
Orange Level Joined: 12 Sep 2009 Location: Hamilton Co, IA Points: 5636 |
Post Options
Thanks(0)
|
Once flashed, generators work either polarity. If not flashed on the polarity change they can fry the cutout in the regulator.Flashing before running is crucial to cutout and sometimes generator life.
Gerald J. |
|
Chalmersbob
Orange Level Joined: 11 Sep 2009 Location: Pennsylvania Points: 2122 |
Post Options
Thanks(0)
|
It may also have a Neg ground regulator on it. Some regulators don't care about ground, others do. Look on the back, it will tell you what you have. Bob
|
|
Gerald J.
Orange Level Joined: 12 Sep 2009 Location: Hamilton Co, IA Points: 5636 |
Post Options
Thanks(0)
|
Usually the difference in the magnetic regulator is in contact material so that the lifetime with the wrong polarity is short, but it works. A solid state regulator hidden in a metal case (fairly common these days) has nanoseconds of lifetime with reversed polarity.
Gerald J. |
|
D-17_Dave
Orange Level Joined: 11 Sep 2009 Location: Mocksville NC Points: 990 |
Post Options
Thanks(0)
|
Why switch it back. The tractor doesn't care what the polarity is.
|
|
CTuckerNWIL
Orange Level Joined: 11 Sep 2009 Location: NW Illinois Points: 22810 |
Post Options
Thanks(0)
|
When you got the tractor somebody may have changed the polarity of the system. If it was working then, you more than likely cooked something that didn't need cooked by changing it to + ground without flashing the generator. Your coil should have polarity switched also. If you run + ground, the pos side of the coil should go to the distributor.
Probably need work on the generator to get it going again. :( |
|
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
|
DSeries4
Orange Level Joined: 12 Sep 2009 Location: Ontario, Canada Points: 7206 |
Post Options
Thanks(0)
|
If the generator and voltage regulator have been off the tractor, they need to be activated before it starts showing a charge. With everything hooked up, short out the BAT and GEN fields on the voltage regulator for a split second. After it sparks, it should be charging.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
DougS
Orange Level Joined: 03 Nov 2011 Location: Iowa Points: 2490 |
Post Options
Thanks(0)
|
As above, repolarize the generator. Negative ground is compatible with so much more. I wouldn't change it back to positive ground. If you haven't repolarized the generator yet and it was working as negative ground, switch it back to the way it was.
|
|
bincitybandit
Silver Level Joined: 14 Aug 2011 Location: North Dakota Points: 125 |
Post Options
Thanks(0)
|
OK, so I arced out the bat and gen terminals on the voltage regulator, but it is still not charging. The regulator is new, but I first hooked the battery up as negative ground and ran the tractor without polarizing it. I assume the first thing to do is try a new regulator as I likely fried mine when I was reversing stuff around? If I get a new regulator, remember to polarize it first, and it still doesn't charge then my generator must be faulty correct?
|
|
ALLIS: B, WC, G, G, D10, D12, D14, D14(NF), D15, D17, D17(NF), D19, D21, D21
MINNEAPOLIS MOLINE: U, U, U(NF), GB JOHN DEERE: L FORD: 871 Select-O-Speed CASE: 600 Combine |
|
CTuckerNWIL
Orange Level Joined: 11 Sep 2009 Location: NW Illinois Points: 22810 |
Post Options
Thanks(0)
|
You can check your generator by removing the belt and running power to it. It will run like a motor if it is working and you hook it up right. YOU DO NOT POLARIZE A REGULATOR. You polarize the generator at the regulator connections.
|
|
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
|
Brian Jasper co. Ia
Orange Level Joined: 11 Sep 2009 Location: Prairie City Ia Points: 10508 |
Post Options
Thanks(0)
|
Since you've polarized, with the engine running say at least 1/2 throttle ground the F terminal, first at the regulator. It should give maximum charge. If it does, you have a faulty regulator. If it doesn't, ground the F term right at the generator. If it charges, the F wire is broken. You can test the gen like Charlie says. Pull the belt, unhook the wires on the gen, and run battery voltage to the A terminal. It should spin fast like a motor. While motoring, ground the F term. It should slow down but continue to motor.
|
|
"Any man who thinks he can be happy and prosperous by letting the government take care of him better take a closer look at the American Indian." Henry Ford
|
|
Butch(OH)
Orange Level Joined: 11 Sep 2009 Location: Lucerne Ohio Points: 3831 |
Post Options
Thanks(0)
|
All the replys are correct and good advise. Sure has been a lot of decent mechanics confused and good equipment screwed up over the years by a battery inavertantly installed backwards, LOL. As they said it can be either way and function perfectly as long as everything was switched tha needs to be. NONE of the old regulators would work either way, they were ground specific. Only some of the newer mechanical ones can be rn either polarity and as Gerald said the electronics are toast in a nanno second. One way to tell if the tractor was converted to negative ground properly or on purpose as it may be, is to look at your igniton coil. Whichever side of the coil ( + or -) is connected to the distributer is what your battery ground termimal should be.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |