This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
WD pto drive gear retaining ring |
Post Reply |
Author | |
CW2 Ryno
Bronze Level Joined: 17 Aug 2020 Location: Nebraska Points: 41 |
Post Options
Thanks(0)
Posted: 28 May 2023 at 6:15pm |
Anyone have any leak replacing the retaining ring for the pto drive gear in front of the hand clutch without a split? Wound up with a WD and upon diagnosing the hand clutch issues found the remnants on the snap ring in the sump.
|
|
Sponsored Links | |
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19590 |
Post Options
Thanks(0)
|
If that snap ring was missing and the gear wasn't retained on the clutch shaft, when you went to disengage the hand clutch, it would pull the gear off the shaft. So ?? how does the hand clutch work ???
|
|
MACK
Orange Level Joined: 17 Nov 2009 Points: 7664 |
Post Options
Thanks(0)
|
Never done it, but I would say it could be done. MACK
|
|
CW2 Ryno
Bronze Level Joined: 17 Aug 2020 Location: Nebraska Points: 41 |
Post Options
Thanks(0)
|
It was sliding the gear back disengaging it from the pto intermediate gear. I think I can get one in, need to find the dimensions of the ring.
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8033 |
Post Options
Thanks(0)
|
leak = luck....changes the whole question.
|
|
Mikez
Orange Level Access Joined: 16 Jan 2013 Location: Usa Points: 8156 |
Post Options
Thanks(0)
|
What’s the part number
|
|
CW2 Ryno
Bronze Level Joined: 17 Aug 2020 Location: Nebraska Points: 41 |
Post Options
Thanks(0)
|
70204085 Is the AGCO part number
Also need the release springs for the clutch plates. AGCO shows two numbers 70226702 And 70223165 Thanks! |
|
Lon(MN)
Orange Level Joined: 11 Sep 2009 Location: Elk River,MN Points: 1908 |
Post Options
Thanks(0)
|
I was able to do it. I suspect worn bearings helped a little.
|
|
http://lonsallischalmers.com
|
|
CW2 Ryno
Bronze Level Joined: 17 Aug 2020 Location: Nebraska Points: 41 |
Post Options
Thanks(0)
|
Looking at the shaft the shoulder is worn and my guess is the snap ring is popping off if they were over zealous on disengaging the hand clutch. Going to see how hard the gear shoulder is and might machine some cone point grub screw and retain it that way. The gear appears to not have any reason to move for me and aft. Tractor is new to me and kind of a hodgepodge. Serial number is 1957 WD45, engine is a WD and the hand clutch was a two disc unit.
|
|
MACK
Orange Level Joined: 17 Nov 2009 Points: 7664 |
Post Options
Thanks(0)
|
Look at snap ring, one side will have a rounded edge, the other a sharp edge. Put the sharp edge toward the hand clutch. MACK
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |