This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
wd45 cooling problems |
Post Reply | Page <123 |
Author | |
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
If the wd and wd45 have the same brake rod I could replace it easy
|
|
Sponsored Links | |
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
If they are not the same where can I get them
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8021 |
Post Options
Thanks(0)
|
same according to parts book
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
All of the sudden the tractor won't start and it turns over very sluggish
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8021 |
Post Options
Thanks(0)
|
Weak battery? Put it on a charger .
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
The battery is fully charged
|
|
Ray54
Orange Level Access Joined: 22 Nov 2009 Location: Paso Robles, Ca Points: 4369 |
Post Options
Thanks(0)
|
After a good battery, check the ground. I had intermittent trouble with one that had corrosion in the cable inside the factory insulation. Finally it pulled apart as I was cleaning the end again. The cable was on the mid 80's tractor when I got it 10+ years ago. Cable looked very good from the outside.
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
I will clean all the connections.
So the bad ground caused the tractor to be sluggish and not start |
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
I cleaned the connection but it still won't start. I have no idea what is wrong I just had it running
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 77909 |
Post Options
Thanks(0)
|
as mentioned, the two most common problems are the battery has not been charging and now needs to be charged up.... or the cables / battery clamps are corroded... Look inside the clamp on the battery cable.. Sometimes you get a black oxide coating that insulates the connection.. Need sand paper or wire brush to get it SHINNY... Look at the battery terminal also... wire brush till BRIGHT.
|
|
Like them all, but love the "B"s.
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
ok i will check that when i get home.
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
i cleaned the battery terminals and it helped with the sluggish turn over but i think the fuel system might be air locked
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
is there a way to lubricate the starter and flywheel so it might work better
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
I've tried everything you told me to and it still won't start for some reason
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
It started and the pully plug blew out
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19566 |
Post Options
Thanks(0)
|
So, put the belt pulley plug back in the hole and get a large 1/2" flatwasher to stick under one of the three bolts near the belt pulley hole to hold the plug so it cannot fall out again.
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
Is there supposed to be hydraulic fluid behind the plug
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
It leaked a lot of hydraulic fluid from the belt pulley plug
Is that bad that fluid came out of there |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19566 |
Post Options
Thanks(0)
|
On the left side of the tractor ahead of the battery box is a short dipstick. This is for the hydraulic pump. Refill it with hydraulic oil. This oil is what came out of the belt pulley hole.
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
Ok so when the plug comes out it emptys the hydraulic pump reservoir
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19566 |
Post Options
Thanks(0)
|
It doesn't "EMPTY" it. It loses a quart or two out of a 6 quart compartment. Refill until the dipstick says it's full.
|
|
hunter321
Silver Level Joined: 11 Jan 2021 Location: 52320 Points: 463 |
Post Options
Thanks(0)
|
Ok I will.
So it is normal for it to have fluid in it |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19566 |
Post Options
Thanks(0)
|
YES. If you had a belt pulley, the oil is what lubricates the gears and bearings.
|
|
Post Reply | Page <123 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |