This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D17 Loose shaft/arm |
Post Reply |
Author | |
Strokendiesel002
Silver Level Joined: 04 Apr 2019 Location: 53158 Points: 252 |
Post Options
Thanks(0)
Posted: 14 Dec 2019 at 8:07pm |
that's a pretty slick trick there Dr nice responses everyone
|
|
Sponsored Links | |
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19572 |
Post Options
Thanks(0)
|
Replace the shaft seal so there's no worries about oil leaks. With a rosebud on your torch, warm up the splined area collar on the arm til it's red all the way around and let it cool down enough to not damage the new seal. Drive the arm into place and let it cool fully. Consider driving it on so far that it binds up on the splines and forget the roll pin. Weld on the bottom to solidify the repair. Weld can always be ground off if needed, but why would you need to with a new seal above it ?? Heating it red and then allowing it to cool off on it's own will shrink it to fit tighter on the worn shaft.
Edited by DrAllis - 14 Dec 2019 at 9:04am |
|
Gary Burnett
Orange Level Access Joined: 11 Sep 2009 Location: Virginia Points: 2853 |
Post Options
Thanks(0)
|
Is there room enough to drill in a couple holes,weld nuts to hold set screws on the outside piece and then tighten up as tight as possible?
|
|
john(MI)
Orange Level Joined: 12 Sep 2009 Location: SE MI Points: 9263 |
Post Options
Thanks(0)
|
I wonder if you cleaned it real good and then forced in the JB Weld for wet applications that you knead to mix? That stuff is pretty strong.
|
|
D14, D17, 5020, 612H, CASE 446
|
|
Lonn
Orange Level Joined: 16 Sep 2009 Location: Назарово,Russia Points: 29773 |
Post Options
Thanks(0)
|
I suppose a cheap fix would be to weld it in two or three spots..... you can always grind it apart again
|
|
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink I am a Russian Bot |
|
CTuckerNWIL
Orange Level Joined: 11 Sep 2009 Location: NW Illinois Points: 22810 |
Post Options
Thanks(0)
|
Permatex has a 5 minute epoxy, that should fix it right up for $5 or less.
Suggested Applications: Complex, multi-piece assemblies. Bonds rigid materials including ceramic, chrome, fabric, fiberglass, glass, hard plastic, metal and rubber Edited by CTuckerNWIL - 13 Dec 2019 at 5:28pm |
|
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
|
jaybmiller
Orange Level Access Joined: 12 Sep 2009 Location: Greensville,Ont Points: 21528 |
Post Options
Thanks(0)
|
OK, humour me ( 2 hrs 'sleep' last night...) What about adding thin steel 'shims' vertically to 'take up the slack' between the faces of the gears or splines or whatever's the proper term( they LOOK like gears to me..) Maybe something like 'banding strapping', a tough , thin steel. Jay
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
|
CTuckerNWIL
Orange Level Joined: 11 Sep 2009 Location: NW Illinois Points: 22810 |
Post Options
Thanks(0)
|
I fixed the flywheel on a 2,500 ton forge press, by filling the gap with an epoxy.
I can't for the life of me, remember the brand name of it. I made a plate that bolted to the shaft, used wedges to kinda line up the flywheel , then used a plastic syringe to fill in the gap. Let it set for 24 hours and they ran that machine 24-7 for about 6 months, till they got parts ahead enough to tear it down and have other repairs done . My brother did a fix like that on a 1300 ton forge press and a year or 2 later I had to tear that press down for a rebuild. We put a LP burner on the shaft, and flywheel hub to get it to just over 600 degrees F and pulled it apart with a 60 ton porta power jack. Edited by CTuckerNWIL - 13 Dec 2019 at 1:01pm |
|
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
|
Lonn
Orange Level Joined: 16 Sep 2009 Location: Назарово,Russia Points: 29773 |
Post Options
Thanks(0)
|
Do both pieces wear a lot or is the wear mostly in the female splines? Can a good metal shop make a new female spline piece to weld in place of old piece?
|
|
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink I am a Russian Bot |
|
Acdiesel
Orange Level Joined: 15 Jun 2012 Location: Rochester Ohio Points: 2512 |
Post Options
Thanks(0)
|
the couple that i have done, I built male shaft splines up with a bead of weld and reground it till it fit tight.
|
|
D19 diesel,D17 diesel SER.3 D14 NF,D14 WF, D15 SER.II wf
D15 SER.2 DIESEL,D15 ser.II nf D12 SER.I, D10 Ser.II 2-720'S Gmc,caterpillar I'm a pharmacist (farm assist) with a PHD (post hole digger) |
|
Strokendiesel002
Silver Level Joined: 04 Apr 2019 Location: 53158 Points: 252 |
Post Options
Thanks(0)
|
Mines probably worse than that, unfortunately... mind if I follow along to see the repair?
|
|
djake
Bronze Level Joined: 14 Nov 2019 Location: Green Isle, MN Points: 34 |
Post Options
Thanks(0)
|
[TUBE]LViGPKjA7dk[/TUBE] Is there any way to fix this short of replacing the parts?
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |