| Author |
 Topic Search  Topic Options
|
victoryallis 
Orange Level
Joined: 15 Apr 2010
Location: Ludington mi
Points: 2878
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 7580 transmission interchangeablility????
Posted: 12 Jan 2019 at 12:16pm |
|
Does a PD out of a 7060 or 7080 go into a 7580? Unknown to me my 7580 was turned up to over 300 hp and since has had multiple issues.
|
|
8030 and 8050MFWD, 7580, 3 6080's, 160, 7060, 175, heirloom D17, Deere 8760
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21467
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 12:27pm |
|
Transmission should be the same. The Power Director clutch has more discs/plates in it on a 7580.
|
|
Ron(AB)
Orange Level
Joined: 27 Dec 2009
Location: Alberta
Points: 959
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 2:21pm |
|
I would check a parts book. I have noticed some gears had changes in the lube system on the early 7000 series to the later. Stuff like oil holes, groves or notches.
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8514
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 5:18pm |
 victoryallis wrote:
Does a PD out of a 7060 or 7080 go into a 7580? Unknown to me my 7580 was turned up to over 300 hp and since has had multiple issues. |
...and you just thought it ran good!
|
|
victoryallis
Orange Level
Joined: 15 Apr 2010
Location: Ludington mi
Points: 2878
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 6:26pm |
SteveM C/IL wrote:
victoryallis wrote:
Does a PD out of a 7060 or 7080 go into a 7580? Unknown to me my 7580 was turned up to over 300 hp and since has had multiple issues. |
...and you just thought it ran good! |
I had my suspicions it was a bit stronger than it should but not that bad.
|
|
8030 and 8050MFWD, 7580, 3 6080's, 160, 7060, 175, heirloom D17, Deere 8760
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21467
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 7:13pm |
|
7580 transmissions are taxed to the max at 185 PTO HP, let alone any more than that. I've worked on two that have taken teeth off of the high range input gears. The tractor weighs a lot and has plenty of rubber on the ground and the tranny gets put under a lot of pressure that a 2wd tractor never sees.
|
|
victoryallis
Orange Level
Joined: 15 Apr 2010
Location: Ludington mi
Points: 2878
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 7:43pm |
|
Currently only have high range no low range.
|
|
8030 and 8050MFWD, 7580, 3 6080's, 160, 7060, 175, heirloom D17, Deere 8760
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21467
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Jan 2019 at 7:49pm |
|
Twisted off low range input shaft I suspect.
That's assuming the Power Director clutch isn't the issue.
Edited by DrAllis - 12 Jan 2019 at 7:50pm
|
|
