This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


WD45 shifter tower
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Fish View Drop Down
Bronze Level
Bronze Level


Joined: 19 Aug 2015
Location: Walkerville
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Fish Quote  Post ReplyReply Direct Link To This Post Topic: WD45 shifter tower
    Posted: 19 Aug 2015 at 7:20pm
Having trouble removing the shifter tower. Appears the reverse fork is holding it up. Last time I drove it it dropped into 3rd gear and I could not get it out. Any advise out there?
Back to Top
Sponsored Links


Back to Top
ac45dave View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 23 May 2015
Location: SE(IN)
Points: 1346 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ac45dave Quote  Post ReplyReply Direct Link To This Post Posted: 19 Aug 2015 at 8:01pm
straight from wd45 service manual.
54 wd-45gas ; 56 wd-45d N/F w/fact p/s ; 63 d-17 sIII N/F gas ; 60 D14 N/F ; 67 d-17 sIV N/F gas ; 63D15 sII W/F; 39rc#667 ; 2021 massey 4710 fwa ; gravely 2 wheel tractors
Back to Top
irlbeck A-C'S View Drop Down
Orange Level
Orange Level
Avatar

Joined: 28 Sep 2009
Location: Crestview FL.
Points: 689 		Post Options Post Options   Thanks (0) Thanks(0)   Quote irlbeck A-C'S Quote  Post ReplyReply Direct Link To This Post Posted: 19 Aug 2015 at 8:32pm
Remove the shift boot. Take out the snap ring and retainer. Pull out the shifter. Do not drop the pin(s) that are in the shift tower. Stick a long screwdriver or something similar down in the hole and pry the fork to the neutral position. Then reinsert the shifter. When it is in neutral the forks will make a rectangle shape that will look a little like this ---> [ 0 ]
when you have the shifter in correctly you will feel a little spring tension on it when you move it side to side. You probably have a worn shifter on the end or where the alignment pins are.

Edited by irlbeck A-C'S - 19 Aug 2015 at 8:37pm
B,C,CA,(2)WC's,(4)WD's,(2) WD45'S, 45Diesel, (2)D12'S Series 2, D12 Hiclear,(2)D12 Series 3, HD3, D17NF (3)D17 Series 4 Diesels, M-100 Grader,8550,A few Lawn tractors lots of other AC stuff    
Back to Top
Fish View Drop Down
Bronze Level
Bronze Level


Joined: 19 Aug 2015
Location: Walkerville
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Fish Quote  Post ReplyReply Direct Link To This Post Posted: 20 Aug 2015 at 5:49am
Thank you I will give it a try.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.


Help Support the
Unofficial Allis Forum