This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Clutch Job on D-14

 Post Reply Post Reply
Author
Message
mherndon View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 30 Apr 2012
Location: Tennessee
Points: 87
Post Options Post Options   Thanks (0) Thanks(0)   Quote mherndon Quote  Post ReplyReply Direct Link To This Post Topic: Clutch Job on D-14
    Posted: 18 May 2012 at 9:39am
I plan on taking the flywheel off to have it turned when I split the tractor to remove clutch.  What are the torque specs for the following?  Flywheel, pressure plate, and any other torques I might run into putting it back together?
 
Mark
 
D-15, Old dealer in Smithville, TN
Back to Top
Sponsored Links


Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825
Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 18 May 2012 at 12:06pm
http://www.imperialsupplies.com/pdf/A_FastenerTorqueCharts.pdf
You can look the bolt size up in this chart.
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
JeffMOnt View Drop Down
Silver Level
Silver Level


Joined: 11 Sep 2009
Location: Ottawa, Ont
Points: 129
Post Options Post Options   Thanks (0) Thanks(0)   Quote JeffMOnt Quote  Post ReplyReply Direct Link To This Post Posted: 18 May 2012 at 12:28pm
Torque specs for flywheel is 75 Ft-lbs.  Not sure on the pressure plate torque, but as Charlie stated you can look it up on the chart.
Back to Top
Chalmersbob View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Pennsylvania
Points: 2122
Post Options Post Options   Thanks (0) Thanks(0)   Quote Chalmersbob Quote  Post ReplyReply Direct Link To This Post Posted: 18 May 2012 at 10:02pm
presure plate is 17-20 ft lbs.
you can't always go by a universal chart. The spec in the book for a 3/8"  head bolt on a G is 55 ft lbs. You will not find that on a bolt spec chart. Bob


Edited by Chalmersbob - 18 May 2012 at 10:02pm
Back to Top
ironac View Drop Down
Silver Level
Silver Level


Joined: 06 Jan 2011
Location: Plainfield IA
Points: 283
Post Options Post Options   Thanks (0) Thanks(0)   Quote ironac Quote  Post ReplyReply Direct Link To This Post Posted: 20 May 2012 at 2:59am
Opps. I just cranked the bolts down on my d14 flywheel
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum