	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Forum Home > Allis Chalmers > Farm Equipment

New Posts

FAQ

oval muffler

Post Reply

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
john n/il. Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 04 Dec 2009 Location: wonderlake ILL. Points: 60	Post Options Post Reply Quote john n/il. Report Post Thanks(0) Quote Reply Topic: oval muffler Posted: 07 Dec 2009 at 8:08pm
	does anyone know how far down your oval muffler on a 171v sits ,down to the tin or lower than the tin mine sits 3 inches above it dont look right

Sponsored Links

Jeff Z. NY Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 11 Sep 2009 Points: 7326	Post Options Post Reply Quote Jeff Z. NY Report Post Thanks(0) Quote Reply Posted: 07 Dec 2009 at 8:27pm
	I don't know the exact inches but all I have seen the muffler sits an inch or two below the tin.

BobPaulusCentrOH Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Access Joined: 11 Sep 2009 Location: Lancaster, Ohio Points: 169	Post Options Post Reply Quote BobPaulusCentrOH Report Post Thanks(0) Quote Reply Posted: 07 Dec 2009 at 8:33pm
	On the D17 series IV gas the muffler clamps to a piece of pipe screwed into the manifold. The pipe flange on bottom of muffler actually touches manifold so it is about 3 to 4 inches on the oval part below surface of the left hood. I know because I had to cut and thread a piece of 1-1/2" or 2" pipe to thread into manifold.

john n/il. Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 04 Dec 2009 Location: wonderlake ILL. Points: 60	Post Options Post Reply Quote john n/il. Report Post Thanks(0) Quote Reply Posted: 07 Dec 2009 at 9:01pm
	thanks I"LL cut some of the nipple off

DSeries4 Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Sep 2009 Location: Ontario, Canada Points: 7447	Post Options Post Reply Quote DSeries4 Report Post Thanks(0) Quote Reply Posted: 07 Dec 2009 at 10:31pm
	Make sure that is the correct muffler. May be a cheap one that someone put on.

john n/il. Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 04 Dec 2009 Location: wonderlake ILL. Points: 60	Post Options Post Reply Quote john n/il. Report Post Thanks(0) Quote Reply Posted: 08 Dec 2009 at 6:58pm
	i bougth this one,but it is not a nelson ,i wish i would of put the 50 towards a nelson this muffler sounds wimpy and faded in 2 weeks.it is an oval .where is a place to get an nelson muffler for 171V

Brian Ahart Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 11 Sep 2009 Location: Missouri Points: 372	Post Options Post Reply Quote Brian Ahart Report Post Thanks(0) Quote Reply Posted: 08 Dec 2009 at 7:23pm
	If none of the forum vendors can get the Nelson, check with your local Cummins/Fleetguard dealer (go to http://www.nelsondiv.com to find a dealer). The D17 IV gas muffler should be 08441T, but be sure to double-check the dimensions before ordering, as they are not inexpensive.
	A-C Weight ID reference and other goodies at brianahart.net

john n/il. Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 04 Dec 2009 Location: wonderlake ILL. Points: 60	Post Options Post Reply Quote john n/il. Report Post Thanks(0) Quote Reply Posted: 08 Dec 2009 at 7:27pm
	thanks brian

Post Reply
Tweet

Forum Jump

Forum Permissions View Drop Down

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Your browser does not support inline frames or is currently configured not to display inline frames.