| Author |
 Topic Search  Topic Options
|
jim 
Bronze Level
Joined: 11 Sep 2009
Location: Underwood Mn
Points: 63
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: wooden sleeve bearings
Posted: 01 Dec 2009 at 9:10pm |
|
|
 |
|
Sponsored Links
|
|
|
Tracy Martin TN
Orange Level Access
Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10837
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 Dec 2009 at 9:11pm |
|
|
|
FRANKO
Bronze Level
Joined: 13 Sep 2009
Points: 26
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 Dec 2009 at 9:53pm |
|
I did a quick internet search and came up with pobcoplastics.com & woodex-meco.com. This may get you started. There are a lot of sources if you search for wood bearings.
|
|
Dusty MI
Orange Level
Joined: 13 Sep 2009
Location: Charlotte, Mi
Points: 5060
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 7:28am |
I was always told that Maple makes the best bearings. Not sure why.
Dusty
|
|
917 H, '48 G, '65 D-10 series III "Allis Express"
|
|
Rawleigh
Orange Level
Joined: 14 Sep 2009
Location: White Stone, VA
Points: 421
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 7:43am |
|
|
|
Gatz in NE
Orange Level
Joined: 11 Sep 2009
Location: Lincoln, NE
Points: 1062
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 8:16am |
some discussions about this from October...
|
|
Gerald J.
Orange Level
Joined: 12 Sep 2009
Location: Hamilton Co, IA
Points: 5636
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 10:45am |
|
Furniture making shop. Will have hard woods, my dad use hickory a lot, and lathe.
Gerald J.
|
|
TomYaz
Orange Level
Joined: 14 Sep 2009
Location: PA
Points: 10340
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 11:43am |
 Rawleigh wrote:
If you are going to use it go with Delrin plastic. That is what I used to remake the bearings on my Allcrop. You will never have to do them again. I got it from Mcmaster Carr. It comes in sheets, blocks, rods and tubes. |
Hey Raleigh, What part(s) on the AllCrop did you use Derlin? I am always looking for alternatives...
Tom
Edited by TomYaz - 02 Dec 2009 at 11:45am
|
|
Rawleigh
Orange Level
Joined: 14 Sep 2009
Location: White Stone, VA
Points: 421
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 8:29pm |
|
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 42036
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 8:57pm |
|
When i was working with chemicals we used a lot of that material in machines where acid was used , held up well in corrosive areas and worked good for most applications.
|
|
Life lesson: If you’re being chased by a lion, you’re on a horse, to the left of you is a giraffe and on the right is a unicorn, what do you do? You stop drinking and get off the carousel.
|
|
TomYaz
Orange Level
Joined: 14 Sep 2009
Location: PA
Points: 10340
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Dec 2009 at 9:03pm |
Rawleigh wrote:
Tom: I replaced the bearings and shafts on the left side of the strawalker. I bought the dimensioned material by the foot from Mcmaster Carr, cut it with a chopsaw and drilled it with regular woodworking tools. They also have a fiber reinforced delrin that has greater shock resistance. I can provide pictures if you want them. |
Bearings and shafts? I would have though this as a replacement for wood bushings..
Yeah some pics would be nice...
|
|
