This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Flywheel bolts- Torque setting?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Brampton 02 gt View Drop Down
Orange Level
Orange Level


Joined: 07 Apr 2011
Location: Erin,ON, Canada
Points: 321 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Brampton 02 gt Quote  Post ReplyReply Direct Link To This Post Topic: Flywheel bolts- Torque setting?
    Posted: 01 Oct 2011 at 1:27pm
I am going to be putting the new clutch on my WD45 .  Is there any torque settings for the flywheel bolts?  The shop manual doesn't list anything.
 
Help is much appreciated!
Back to Top
Sponsored Links


Back to Top
Jeff Z. NY View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Points: 7326 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jeff Z. NY Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2011 at 1:37pm
For the diesel they say 95 to 105
I Love Meatballs and Dumplings on Toast with Gravy and Rosemary and ??? {Open For Suggestions}
Back to Top
Brampton 02 gt View Drop Down
Orange Level
Orange Level


Joined: 07 Apr 2011
Location: Erin,ON, Canada
Points: 321 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Brampton 02 gt Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2011 at 1:40pm
Mine is gas.  Sorry I didn't clarify.
Back to Top
Jeff Z. NY View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Points: 7326 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jeff Z. NY Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2011 at 2:32pm
I figured that.
I would think the diesel specs would be pretty close to the gas if not the same.
I can't count the number of engines I built by just getting them good and tight without knowing what torque they were at.
After you get them evenly snug go around again with a small 1/2 breaker bar.
You should be fine.
I Love Meatballs and Dumplings on Toast with Gravy and Rosemary and ??? {Open For Suggestions}
Back to Top
TedBuiskerN.IL. View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Davis, IL.
Points: 1959 		Post Options Post Options   Thanks (0) Thanks(0)   Quote TedBuiskerN.IL. Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2011 at 5:46pm
The gas is lower, it's either 65 or 85 can't remember for sure, and my book is out in the shop.
Most problems can be solved with the proper application of high explosives.
Back to Top
Chuck(ONT) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Ontario
Points: 1055 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Chuck(ONT) Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2011 at 6:20pm
My service manual for WD45 gas flywheel says,
lockwashers and capscrews, tighten to 50 ft. lbs.
Never take life too seriously.

Nobody gets out alive anyway!

1C 1 WD45 1 AC180
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.035 seconds.


Help Support the
Unofficial Allis Forum