![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
| The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History | |
WD45 carb question |
Post Reply
|
| Author | |
WhiskeySup
Orange Level
Joined: 17 Apr 2011 Points: 233 |
Post Options
Thanks(0)
Quote Reply
Topic: WD45 carb questionPosted: 31 Aug 2011 at 5:40am |
|
Finally got to work my 45 last weekend bush hogging but the carb would not stay running unless the choke was held out all the way. Fiddled around with the carb and the only way it would run is if the main load valve was turned in all the way. Not familiar with this carb but she was a champ cutting very thick 7 foot tall weeds. Any suggestions? Also, I see where the transmission fill port is but how do you tell if it is full?
Thanks
Jon.
|
|
![]() |
|
| Sponsored Links | |
![]() |
|
jccleav
Orange Level
Joined: 11 May 2011 Location: Indianola IA Points: 211 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 8:09am |
|
The carb might need cleaned. there should a a dip stick to tell you when it is full. If I remember correctly it is located by the battery on the left side.
|
|
![]() |
|
WhiskeySup
Orange Level
Joined: 17 Apr 2011 Points: 233 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 8:16am |
|
Besides the engine oil dip stick, the only other one is next to the dist. cap. Which one is that?
|
|
![]() |
|
KY
Silver Level
Joined: 08 Dec 2009 Location: Kentucky Points: 371 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 10:28am |
|
On the left side of the tractor there is a dipstick beside the battery box. This is for hydraulics and is self explanitory on oil level. Beside the foot cluth pedal there are 2 square filler plugs on the side of the trans housing. remove each, oil should be level full in hole. Some folks use gear oil in the trans/diff like original, others use universal hydraulic oil. Its all in your preference. I use gear oil cause its thicker and doesnt leak out as fast!
|
|
![]() |
|
WhiskeySup
Orange Level
Joined: 17 Apr 2011 Points: 233 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 11:30am |
|
Many thanks for the info-the manual is not very clear. Will be doing lots more bush hogging this weekend (going to be in the mid 90's) and wanted to be sure she didnt get thirsty.
Jon.
|
|
![]() |
|
Steve in NJ
Orange Level Access
Joined: 12 Sep 2009 Location: Andover, NJ Points: 12017 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 1:19pm |
|
When the choke needs to be on or partially on, you're fatting up the fuel mix. This could mean a few things. Either the engine has a fuel delivery problem, a lean condition due to a plugged idle circuit, or fuel bowls full of crud. As JC mentioned, it probably needs a good overhaul. We offer carb rebuilding if interested. We should be back up and running by the first week in October... |
|
![]() |
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009 Location: NW Illinois Points: 22825 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 5:55pm |
There is no dipstick for the tranny & rearend. The dipstick on the left below the battery box is for hydraulic oil. The dipstick for engine crankcase oil is on the right side of the block behind the distributor.
|
|
|
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
|
![]() |
|
Chalmersbob
Orange Level
Joined: 11 Sep 2009 Location: Pennsylvania Points: 2122 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Aug 2011 at 10:27pm |
|
You might want to remove the plug on the bottom of the carb, or take out the main jet, and let the fuel flow into a bucket for a few minutes. If you don't have a good flow, remove fuel line and check flow at that point. Work your way back until you get a good flow. Bob
|
|
![]() |
|
Post Reply
|
|
|
Tweet
|
| Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |