This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


7020 Allis
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
mnjoe View Drop Down
Bronze Level
Bronze Level


Joined: 12 Sep 2009
Location: MN
Points: 41 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mnjoe Quote  Post ReplyReply Direct Link To This Post Topic: 7020 Allis
    Posted: 07 May 2011 at 9:18pm
I;m having trouble with the indictator lights. I have power to the circuit board but my oil pressure light and trans oil pressure light will not come on when I turn on the key. The alternator comes on..The other 2 light come on as soon as I push the starter like they should. I'm thinking of adding mech. oil pressure gauges. What kind of pressures will come off the transmission line..if I tee off of the sending unit? Thanks
Back to Top
Sponsored Links


Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 07 May 2011 at 10:13pm
Are the bulbs good in the two that don't come on? The circuit board also goes bad.
MACK
Back to Top
mnjoe View Drop Down
Bronze Level
Bronze Level


Joined: 12 Sep 2009
Location: MN
Points: 41 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mnjoe Quote  Post ReplyReply Direct Link To This Post Posted: 07 May 2011 at 10:28pm
The bulbs are good. Using my meter i read power off of the wiring harness..butnot on the board.  Had to resolder the bulb holder. Cleaned up the contacts. I'd like to add gauges to see what I have for pressures. Thanks
Back to Top
mnjoe View Drop Down
Bronze Level
Bronze Level


Joined: 12 Sep 2009
Location: MN
Points: 41 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mnjoe Quote  Post ReplyReply Direct Link To This Post Posted: 08 May 2011 at 9:02am
Lost power from the transnission oil pressure to the circuit board....my parts book shows the sender up front under the radiator. I have a early 7020 did they move it? Maybe my eyes just can't see it. Found 2 sending units behind the small fuel tank. The wire colors don't for what I'm looking for. Thanks
Back to Top
Lynn Marshall View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 13 Sep 2009
Location: Dana, Iowa
Points: 2440 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lynn Marshall Quote  Post ReplyReply Direct Link To This Post Posted: 08 May 2011 at 9:39am
Power director tractor tranny filter and sending unit are under radiator.Power shift tractor tranny filter is on right hand rear in canister.Power shift tranny sending unit is screwed into an elbow fitting,between main fuel tank and tranny housing.It's a little tricky to see,but can be replaced with proper tools.Also,there is no power or voltage thru the wire.It just provides the ground to make the circuit.Same way for the engine oil pressure too.
Back to Top
mnjoe View Drop Down
Bronze Level
Bronze Level


Joined: 12 Sep 2009
Location: MN
Points: 41 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mnjoe Quote  Post ReplyReply Direct Link To This Post Posted: 08 May 2011 at 9:52am
Thanks...I bought this tractor used. I bought a manual and started to read about the transmission pressure light should come on. It did last year. Thanks for telling me about the location. I can run a new wire to the circuit board....did it..that now works...The engine oil pressure won't work on the board. Might just add a light socket. Thanks again I found my answers
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.102 seconds.


Help Support the
Unofficial Allis Forum