| Author |
 Topic Search  Topic Options
|
Jgriffis03 
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Looking for Hd6 part
Posted: 18 Mar 2026 at 9:42pm |
|
I’m needing the intermediate shifting shaft. If anyone has one for sale I would greatly appreciate it. Number 5 on the callout for parts diagram of the shift tower. Thank you in advance
|
 |
|
Sponsored Links
|
|
|
Codger
Orange Level
Joined: 23 Dec 2020
Location: Utopia
Points: 2665
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 7:20am |
|
Have made that exact part a couple of times in the past. 4140, or 4340 Alloy steel will offer enough surface "toughness" without heat treat to last. Have a machinist bore the shift handle, (#6) round and bush this with oilight bronze, or drill and tap your new shaft, (pivot pin) for a grease zerk, and cross drill for grease path keeping it tended to. While the shift lever is out always a good idea to have the lands where the pivot screws butt against cleaned up also. Makes for a nice tight shifter again as long as the shifting forks and shafts are in good condition. These always need touched up also as wear items.
|
|
That's All Folks!
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8900
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 9:31am |
|
What’s the part number
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 9:45am |
|
I’m sorry all, it’s number 6 on the callout.
P/N: 098089
Or
P/N: 086705
It’s the whole lower shaft
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 9:46am |
|
The whole shift lever is missing haha. My issue is that I’m not sure I can get one machined without precise measurements of one first.
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 1625
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 3:07pm |
Maybe check with General Gear and Machine in Boise, Idaho
|
|
Codger
Orange Level
Joined: 23 Dec 2020
Location: Utopia
Points: 2665
|
Post Options
Thanks(0)
Quote Reply
Posted: 21 hours 37 minutes ago at 5:35pm |
|
Definitely be cheaper to obtain used, but I can make one if needed.
|
|
That's All Folks!
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 hours 52 minutes ago at 9:20pm |
|
How much would you charge for one?
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 hours 13 minutes ago at 9:59pm |
|
I checked there and they said the one they had they just threw out because it was worn out
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 1625
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 hours 57 minutes ago at 11:15pm |
|
Forum member gemdozer has some parts but he said his yard is closed until Spring, also, he is in Canada
|
|
Codger
Orange Level
Joined: 23 Dec 2020
Location: Utopia
Points: 2665
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 hours 3 minutes ago at 4:09am |
No real idea as time and materials would be in play. Realistically probably $350 - $400 is in the ballpark. I have a good piece/pattern to follow. Have never made one complete as you need but have rebuilt several.
Before putting much into this tractor I'd suggest you manually get into each gear and operate it. You can do this by moving the shift forks with a pry.
Seen a lot of 'Starry Eyed" auction, and sale purchases over the years reveal underlying buget busting problems underneath requiring wheelbarrows rather than shovelfulls of money to fill the pit.
Edited by Codger - 10 hours 18 minutes ago at 4:54am
|
|
That's All Folks!
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: 5 hours 56 minutes ago at 9:16am |
|
Little back story here, it was parked up about 40 years ago and I bought it for 600 bucks and I honestly didn’t have the equipment to pull it out of there so as the mechanic I am I got it running an drove it out of the hole it was stuck in. The only thing I need to do now is replace some hydraulic lines and free up steering clutches. I did try and shift in all the gears hand itinerary shifts pretty smooth and they all grab
|
|
gemdozer
Orange Level
Joined: 17 Sep 2009
Points: 1074
|
Post Options
Thanks(0)
Quote Reply
Posted: 2 hours 7 minutes ago at 1:05pm |
|
I should have this lever shift and I could check late next week
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: 1 hour 13 minutes ago at 1:59pm |
|
Yeah I’d sure appreciate it. Really out of options at this point
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 42254
|
Post Options
Thanks(0)
Quote Reply
Posted: 33 minutes ago at 2:39pm |
|
Dont have the parts list handy - is that the part that fits into shift tower and has shift lever clamp to it ?
The part that actually moves the shift rails in trany - ball type end and , pivot point center and round shaft through shift boot
|
|
Life lesson: If you’re being chased by a lion, you’re on a horse, to the left of you is a giraffe and on the right is a unicorn, what do you do? You stop drinking and get off the carousel.
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 minutes ago at 2:52pm |
Yes, its the lower shaft that actually sit inside the transmission and has a big oval hole through it which is where the bushing goes. I will see if i can add a picture
|
|
Jgriffis03
Bronze Level
Joined: 18 Mar 2026
Location: Iowa
Points: 10
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 minutes ago at 2:53pm |
|
|
|
