This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Balpak bearings
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
mruhlig77 View Drop Down
Orange Level
Orange Level


Joined: 19 Aug 2014
Location: central Indiana
Points: 588 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mruhlig77 Quote  Post ReplyReply Direct Link To This Post Topic: Balpak bearings
    Posted: 29 Apr 2023 at 3:34pm
are there one or two bearings in a balpak....need to see a picture of one cut apart...Mark
Back to Top
Sponsored Links


Back to Top
ac hunter View Drop Down
Orange Level
Orange Level
Avatar

Joined: 05 Jan 2011
Location: OHIO
Points: 1044 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ac hunter Quote  Post ReplyReply Direct Link To This Post Posted: 29 Apr 2023 at 4:39pm
look on the farm equipment-knowledge base on this forum; there is an excellent post on those bearings.
Back to Top
mruhlig77 View Drop Down
Orange Level
Orange Level


Joined: 19 Aug 2014
Location: central Indiana
Points: 588 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mruhlig77 Quote  Post ReplyReply Direct Link To This Post Posted: 30 Apr 2023 at 12:55pm
Thanks Mr. Hunter...but it does not have that cross section info....Mark
Back to Top
Allis dave View Drop Down
Orange Level
Orange Level


Joined: 10 May 2012
Location: Northern IN
Points: 3007 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Allis dave Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2023 at 6:48am
Hello Mark,
I'm the one that wrote that knowledgebase bearing post. Further down in the article it was a comment including one of the original pics of a failed bearing that I took apart. All parts are in that pic.

The bearing assembly includes a single bearing, 2 bushings(spacers), and two seals. Pressed through the center of the bearing, bushings, and seal, is a tube wiht a round or hex center depending if you have a round or hex shaft.
All of this is pressed inside the large exteral tube that you see when you look at the disk. 
Back to Top
mruhlig77 View Drop Down
Orange Level
Orange Level


Joined: 19 Aug 2014
Location: central Indiana
Points: 588 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mruhlig77 Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2023 at 7:07am
Thanks...but you are saying the just one bearing is in the exact middle...there must be a lot of air space  between the bearing and the outside seals....hence why needed a crosssection picture...there isn't one in my disk book either....Thanks for trying to help...Mark
Back to Top
Alvin M View Drop Down
Orange Level
Orange Level


Joined: 24 Jun 2018
Location: PA
Points: 795 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alvin M Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2023 at 11:23am
I use two of BCA 88107A in each one no other parts are needed they are sealed
Back to Top
Mikez View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 16 Jan 2013
Location: Usa
Points: 8654 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mikez Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2023 at 11:30am
The way I read it mark isn’t asking the fix. He’s asking what’s in the original bearing.
Back to Top
Alvin M View Drop Down
Orange Level
Orange Level


Joined: 24 Jun 2018
Location: PA
Points: 795 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alvin M Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2023 at 11:34am
Press it apart then you will see ball bearing
Back to Top
Allis dave View Drop Down
Orange Level
Orange Level


Joined: 10 May 2012
Location: Northern IN
Points: 3007 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Allis dave Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2023 at 11:35am
You're correct Mark. There is just one bearing in the middle. Some of that "air" space is filled by those bushings. The little that was left I don't know if it was all filled wiht the seal or what. It's been awile, but in the picture the seal looks pretty thick.
I filled up my air space wiht the felt seal and rubbed greas into it.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum