This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D17 brakes and drum replacement |
Post Reply |
Author | |
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
Posted: 06 Feb 2023 at 6:18pm |
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Sponsored Links | |
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
Had a really good day today. Finally got around to replacing the brakes and right side drum on my D17. Got along so well on the right side Mutt and I started the left side. Replaced left and right pinion seals, right side drum, installed new brake pads. Started the left side, new brake pads, have the drop housing off and also replacing the axle oil seal. Also replaced both housing pan gaskets, cleaned, followed by new oil. Having a issue getting the snap ring out so we called it a day. I’m pleased with our progress in 6 hours.
Edited by AC720Man - 06 Feb 2023 at 6:31pm |
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
captaindana
Orange Level Joined: 14 Sep 2009 Location: Fort Plain, NY Points: 2382 |
Post Options
Thanks(0)
|
It’s surely a chore!
|
|
Blue Skies and Tail Winds
Dana |
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
You got that right captain, but it went better than I anticipated.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
MACK
Orange Level Joined: 17 Nov 2009 Points: 7664 |
Post Options
Thanks(0)
|
What snap ring are you trying to remove? MACK
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
Axle gear snap ring. I’m letting the remaining oil drip out the housing overnight to get a better look at it. My factory manual says to remove it by going up through the bottom of the final drive housing. Getting a different pair of snap ring pliers tomorrow to get a better hold of it.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
I tried going in from the side were I removed the inner bearing cap. I removed the bolt, washer and shim, bearing cone. Just no room to remove it unless the bearing cup is removed.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
MACK
Orange Level Joined: 17 Nov 2009 Points: 7664 |
Post Options
Thanks(0)
|
It can try you. Use two big screwdrivers to pry it back on. MACK
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
Finished up around 1 today Mack. Took the axle to my local machine shop and had the bearing removed so I could replace the seal. Pressed the bearing back on, and reinstalled in the drop housing. Can’t tell how nice it is to have functional brakes. And I finally can lock my brakes without it drifting off. Easy to lock a brake left or right brake and spin it on a dime. Now, need to fix my power steering leak ugh. That repair will start next week.
Edited by AC720Man - 07 Feb 2023 at 6:19pm |
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
JC-WI
Orange Level Access Joined: 11 Sep 2009 Location: wisconsin Points: 33678 |
Post Options
Thanks(0)
|
Your pic suddenly made me feel jealous. Nice straight looking tractor.
|
|
He who says there is no evil has already deceived himself
The truth is the truth, sugar coated or not. Trawler II says, "Remember that." |
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4709 |
Post Options
Thanks(0)
|
Thanks JC, it’s a work in progress. She has some dings but I have completed a lot of repairs. It has the wrong shroud and grill on it due to something coming off of the loader and damaging it. I purchased the tractor without the loader. I have the correct shroud and grill. It’s a 1959 3 bar grill.
Edited by AC720Man - 07 Feb 2023 at 9:58pm |
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |