This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


g2800 lp
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Topic: g2800 lp
    Posted: 25 Jan 2023 at 9:44am
going to go look at a tractor for parts 190 xt with a g2800 lp  so i do not know any thing about the enginge but it looks like a lot higher compression  (on tractor data) mostly interested in the engine for a puller other parts on the tractor have been robbed   what is the crankshaft nut size so i can take a wrench with to turn the engine over 
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21490 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jan 2023 at 10:59am
1 5/16"  wrench I think.
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jan 2023 at 11:20am
so is this a good engine i did not even know that it exsisted untill i seen the tractor last summer
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21490 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jan 2023 at 1:20pm
They were fine but I'm sure suffered the same problem the regular gas models did.......the piston top could break off and the skirt was left going up and down in the sleeve. I don't believe there are any piston/sleeve kits available anymore for gas and surely not LPgas. If you want high compression for a puller, use diesel pistons and just mill open the bowl some more and get 12 or 13 to 1 compression. LPgas is only 9.3 to 1,  I think.
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jan 2023 at 8:35pm
I might have a set if 4.1/8 forged pistons for it. Have a block bored for 226 AC sleeves.                 Call 660 663 9173.                      MACK
Back to Top
groundhog55 View Drop Down
Silver Level
Silver Level
Avatar

Joined: 26 Apr 2011
Location: nw in
Points: 217 		Post Options Post Options   Thanks (0) Thanks(0)   Quote groundhog55 Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2023 at 7:36am
I think that I know were there is a set of piston and sleeves for that engine.
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2023 at 9:30am
could this engine go in place of the engine in a wd45d or d 17d or d19 and use  as a farm tractor .      4 1/8 pistons and sleeves what c.i. does that come up to?      might have to start a new post in the pulling section
Back to Top
DON G View Drop Down
Silver Level Access
Silver Level Access
Avatar

Joined: 14 Feb 2014
Location: Lowpoint, IL
Points: 407 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DON G Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2023 at 7:09pm
I had one. 265ci. Did not like it. Traded for 190XTD ,lots of power ran 9 years, lost hearing. Traded for 7000. big improvement.

Edited by DON G - 26 Jan 2023 at 7:14pm
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21490 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2023 at 7:21pm
A 265 cube engine was the G-2500 used in the 180 and 190, not a 190XT gas. Was only 75 HP on the 190.
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2023 at 8:46pm
4 1/8 bore makes it 340 ci.                   MACK
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2023 at 10:32pm
i am going to stop and look at it tomorrow i am thinking this will be puller matierel for the one pull we have a year 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.188 seconds.


Help Support the
Unofficial Allis Forum