| Author |
 Topic Search  Topic Options
|
Kevin210 
Silver Level
Joined: 08 Oct 2018
Location: Indiana
Points: 404
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: clutch alignment tool
Posted: 26 Sep 2021 at 9:05pm |
|
I'm looking for an alignment tool for a 210 allis,would like to have one of my own if possible.
I'm in Indiana.
|
 |
|
Sponsored Links
|
|
|
Charlie175
Orange Level
Joined: 11 Sep 2009
Location: Shenandoah, VA
Points: 6366
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 5:41am |
|
Some of the manuals show you a diagram of the tool so you can make it.
|
|
Charlie
'48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24334
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 5:57am |
|
shh, I used a broom handle,20 year ago and Troy's still happily running.
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
plummerscarin
Orange Level Access
Joined: 22 Jun 2015
Location: ia
Points: 3750
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 6:23am |
|
Jay, it's no secret. I did the same on a 170
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 7:17am |
|
With a recessed flywheel, it caint be off very far. MACK
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21359
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 7:17am |
|
Pretty sure the D21/210/220 takes the exact same tooling as any big frame Farmall from 806 and up.
Edited by DrAllis - 27 Sep 2021 at 7:18am
|
|
Charlie175
Orange Level
Joined: 11 Sep 2009
Location: Shenandoah, VA
Points: 6366
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 8:12am |
|
|
|
Charlie
'48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24334
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 8:30am |
|
was told every 'clutch kit' is sold WITH the alignment tool, maybe hit local garage, see what they have...
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5125
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 1:50pm |
|
I just replaced both clutches in my 160, as Charlie said my manual gave me exact measurements for my local machine shop to make me one out of aluminum. $25, so much better than the plastic ones that can break or flex.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
DougG
Orange Level
Joined: 20 Sep 2009
Location: Mo
Points: 8246
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 3:56pm |
|
This is my experience, and I always try to do things right- the clutch disc is so close to being centered- gently tighten the pressure plate bolts ; look from behind , and center the disc with a screwdriver or something like that in the pilot bearing - its very simple
Edited by DougG - 27 Sep 2021 at 3:57pm
|
|
DaveSB
Silver Level
Joined: 04 Aug 2012
Location: mocksville, nc
Points: 243
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 5:09pm |
|
Maybe I’m just lucky, but I haven’t used a clutch alignment tool for the past ten years, just eye ball them and slide the tractor together.
Good luck
if you need one you can make one out of wood on a wood llathe, unless extremely heavy clutch plate.
|
|
1948 C, 1953 CA, 1948 WD, 1961 D-17 Series 2 Diesel, 1939 WC, 1957 D14
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5125
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Sep 2021 at 8:41pm |
|
That may work on a tractor with just a transmission clutch, I wouldn’t attempt it with a dual stage clutch such as in my 160. The clutches can’t take misalignment and will bend very easily. The entire clutch assembly weighs 70 lbs.
Edited by AC720Man - 27 Sep 2021 at 8:43pm
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Kevin210
Silver Level
Joined: 08 Oct 2018
Location: Indiana
Points: 404
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 Oct 2021 at 9:06pm |
|
Finally got the MK II 3700 engine bolted up this morning on the 210
and did some painting.
I only have 3 days a week to work on it due to working 12 hour shifts
Monday-Thursday and have other things to do also but it's coming along.
|
|
