| Author |
 Topic Search  Topic Options
|
DCAC 
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Torque
Posted: 10 Apr 2021 at 7:17pm |
Hello Gentlemen, I'm putting the head back on the 170 gas, and was wondering what everyone uses to get the proper torque values on the nuts that hold the water outlet to the block. Was thinking of using a crow foot adapter, but wasn't sure if that would effect anything or not. Any advice is appreciated, thank you!
|
 |
|
Sponsored Links
|
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Apr 2021 at 7:22pm |
|
Should have said water outlet to the head
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Apr 2021 at 9:12pm |
|
There was a special tool for that. Easy to make.
|
|
plummerscarin
Orange Level Access
Joined: 22 Jun 2015
Location: ia
Points: 3826
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Apr 2021 at 9:18pm |
|
I had no luck using a crow foot. Ended up getting a 2" long box wrench with ⅜ square drive on the end then calculated the new torque wrench setting.
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Apr 2021 at 9:24pm |
|
Mack, do you have pics or any info on this tool ?
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Apr 2021 at 9:27pm |
|
plummerscarin, how did you the recalculations?
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 86221
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Apr 2021 at 9:45pm |
https://belknaptools.com/extensions-calculator/
Edited by steve(ill) - 10 Apr 2021 at 9:47pm
|
|
Like them all, but love the "B"s.
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2021 at 9:18am |
|
Thanks everyone, I'll see what i can come up with.
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3821
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2021 at 11:36am |
|
if the adapter is at a right angle no other calculation is needed , only 90*
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2021 at 12:10pm |
|
Are you referrig to something like a distributor wrench?
|
|
Jim.ME
Orange Level
Joined: 19 Nov 2016
Location: Maine
Points: 961
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2021 at 12:36pm |
Here is a link to some at McMaster Carr.
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2021 at 8:01pm |
|
Many thanks, gentlemen! Going to order an adapter tomorrow. Thanks again!
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Apr 2021 at 8:38pm |
|
Yes, like a distributor wrench with square drive in top. MACK
|
|
DCAC
Orange Level
Joined: 20 Oct 2018
Location: east central SD
Points: 511
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Apr 2021 at 6:44am |
|
Thank you Mack!
|
|
