![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
WD45 Gearshift retaining washer |
Post Reply ![]() |
Author | |
Sanchez ![]() Bronze Level ![]() Joined: 01 Apr 2020 Location: Alberta Points: 47 |
![]() ![]() ![]() ![]() ![]() Posted: 01 Apr 2020 at 11:27pm |
Does anyone know the dimension of the retaining ring to hold down the shifter? A few places that sell the washer and snap ring kits say the washer has an OD of 1.368 ID 0.998 0.254 thick, but the OD of the Snap ring is not given. If anyone has the dimension of the snap ring I'd like to pick one up a a local bearing supply shop, its easier than paying shipping /duty for parts shipped north of the border.
|
|
![]() |
|
Sponsored Links | |
![]() |
|
Jim.ME ![]() Orange Level ![]() Joined: 19 Nov 2016 Location: Maine Points: 938 |
![]() ![]() ![]() ![]() ![]() |
If someone does not post the dimensions for you should be able to use the washer OD to gauge how much larger the snap ring is. You could get a few snap rings in steps of OD larger than the washer OD to try, since they will be less expensive locally. It appear a D14 and some others use the same snap ring # 70202875.
|
|
![]() |
|
Gary ![]() Orange Level Access ![]() Joined: 13 Sep 2009 Location: Peterborough,On Points: 5201 |
![]() ![]() ![]() ![]() ![]() |
FYI checked the Parts Catalog WD and WD-45 use the same Parts Snap Ring 202875, Washer 207772 Gary |
|
![]() |
|
Sugarmaker ![]() Orange Level ![]() ![]() Joined: 12 Jul 2013 Location: Albion PA Points: 8172 |
![]() ![]() ![]() ![]() ![]() |
Sanchez,
Welcome! I like the WD45's too!:) If I remember I can try to measure the used one I just took out of my WD45.
Grrrrrrrr! Regards, Chris |
|
D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet.
|
|
![]() |
|
Sanchez ![]() Bronze Level ![]() Joined: 01 Apr 2020 Location: Alberta Points: 47 |
![]() ![]() ![]() ![]() ![]() |
Thanks for the quick response, I cut a washer to those dimensions on the lathe the other day, I just need to pick up a snap ring for it. My problem is the tractor is out at my Uncles place so I haven't been able to test fit or take any better measurements. From the photos I've seen it looks like the washer has a rounded inner radius that must contact the ball of the shifter, or is there some other type of seat that contacts the shifter ball.
|
|
![]() |
|
Alberta Phil ![]() Orange Level ![]() ![]() Joined: 13 Sep 2009 Location: Alberta, Canada Points: 3661 |
![]() ![]() ![]() ![]() ![]() |
Don't know where you are in Alberta, but check with your local Agco dealer, they may have it. The one I deal with in Camrose is usually pretty good at finding earlier parts.
|
|
![]() |
|
Sugarmaker ![]() Orange Level ![]() ![]() Joined: 12 Jul 2013 Location: Albion PA Points: 8172 |
![]() ![]() ![]() ![]() ![]() |
I measured my used ring and it was 1.50 o.d. Hope that helps.
Regards, Chris
|
|
D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet.
|
|
![]() |
|
Sanchez ![]() Bronze Level ![]() Joined: 01 Apr 2020 Location: Alberta Points: 47 |
![]() ![]() ![]() ![]() ![]() |
Thanks Chris, that helps for sure. I should be able to find a retaining ring with that OD to retain a 1-3/8 washer. Phil, I thought AGCO was only in the US, after some digging it turns out the Canadian version is Agriterra and they are able to bring in the washer and retaining ring, although at $14 and $16 each I'm going to try my homemade version first.
Thanks for the heads up, I'm sure I'll need to get parts from them sooner or later.
|
|
![]() |
|
Alberta Phil ![]() Orange Level ![]() ![]() Joined: 13 Sep 2009 Location: Alberta, Canada Points: 3661 |
![]() ![]() ![]() ![]() ![]() |
They can be pretty pricey on some items, but reasonable on others. They wanted over $40 each for new exhaust valves for a gas D19, but intakes were about $12. We got the exhaust valves from an Ontario supplier for $17.36 each. Welcome to the forum!!
|
|
![]() |
|
BillinAlberta ![]() Silver Level ![]() ![]() Joined: 12 Sep 2009 Location: Saskatchewan Points: 331 |
![]() ![]() ![]() ![]() ![]() |
Yeah Welcome to the forum.
Good old tractors and there are a number of AGCO dealers in Alberta. The parts and prices for the old machines are all over the map but I always check with the dealer first. I deal with Pentagon Farm Centre Lacombe.
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |